YMEDX500BW0 Maytag - Instructions

I have not received the parts yet waiting on the motor, can’t put the blower fan in without the motor, ordered it , Jan 23rd, still no motor, have to go to laundry mat, have you ever had to do that with 7kids, and you and your wife’s laundry, probably not, because you would have had your motor by now. Maybe you can help me with the part so I can redo a testimonial here for you. 19 days and still waiting

removed old gasket took door off 4 screws. cleaned seal area applied glue put on gasket easy

Take the door off of the dryer. Lay it on a towel. Remove old gasket. Clean the channel the door gasket fits into with glue remover. Squeeze high temperature glue into the channel, let the glue set up. Put the new gasket into the channel, tape it down in a few places. Let it sit 24 hours for the glue to set up. Put the door back on. You can put the door on immediately as long as you don't use the dryer for 24 hours. Easy.

Remove top, front and drum. Top is removed by sliding a putty knife under the front corners and pushing the tabs back. Front is held with screws. Disconnect two electrical connectors. Rollers are easily accessible and changed.

I followed the video. So easy..

The cycling thermostat was found to be not working when I checked it with a ohm meter. I ordered the part waited and installed it and it work just fine.

Replaced the most worn drum wheel any lubed the belt tension arm pulley. The noise didn't go completely away. There are 4 drum wheels. I need to order 3 more wheels and the tension arm now.

My dryer started squeaking and I thought it was the drum rollers, so I bought a set. When I attempted the repair and got as far as removing the dryer drum and I decided to spin the shaft on the motor and that was where the squealing was coming from. I put the rollers on and reassembled the dryer. One day later the motor seized up. Ordered a new motor and installed it with no problems. The nut on the back of the motor ended up being a 20mm wrench. Motor cost me $105.56 and the maintenance kit (ps37308) (2 rollers,4 clips, button clip, new idler pulley and belt) cost $32.08. It cost a total of $137.64 in repairs with no labor costs and I accomplished it in under an hour. Minor handyman skills needed or find a friend who is handy. My dryer is 14 years old and now is running like new again. I used the 50% rule, if a repair exceeds 50% of the cost of a new machine, replace it, if the repair can be done for less than 50% of the cost of a new on, fix it.

I put in the new parts but it still did not work, Turned out the Thermal Fuse Blew,removed the two wires and clipped them together and the Dryer worked, have to replace the Thermal fuse and everything will be OK.

first with the dryer unpluged ,i removed the wires from the upper thermal cut off ,then with a nut driver i removed it . replaced it with the new one and reattatched the two wires then the same on the bottom thermal . to replace the spring i removed the two screws pulled out the switch and spring at the same time ,removed the broken spring and replaced it onto the switch then placed it back into the dryer and replaced the screws.! everything worked like it han never been broke! my wife is verry happy!!!

I removed all the screws to the back panel to gain access to the inside. checked all thermostats and fuses for conductivity (0.001 ohms) resistance. noticed the thermal cut off fuse (thermostat) was showing no conductivity (infinite ohms or OL). FYI the thermal cut-off kit I purchased included both the thermal cut-off fuse(why this is called fuse is a lie its actually a thermostat) and high limit thermostat. I'm seeing alot of users purchasing these seperate but it isn't neccessary. You might need some wire strippers with a crimper though to install everything.

Remove backpanel, ohms cut off thermostat, no good, disconnet two wires from defective part and installed a new one.

I removed the two screws underneath the lent trap the removed the two screws that held the dryer switch assembly. I then lifted up the top and disconnected the door switch assembly. Removing the door switch assembly was the toughest part, and it was not difficult. Simply grab a pair of pliers and pull. I the attatched the new door switch assembly and the four screws and my dryerwas as good as new. I paid around $20.00 including shipping and saved myself a couple of hundred dollars

I attempted to take the back panel off the dryer only to discover all I had to do (after removing 10 or so screws) is remove the lower base plate in the front of the dryer. I also had removed the door which turned out to be unnecessary. After removing a guard in front of the heating element (2 screws) I yanked the the element housing that contained the heating element and then disconnected the 6 wires. Using my first ever, newly bought multi meter for only $9.99 from Radio Shack, I turned the dial to the infinity section and check the element for continuency. I did this by touching the meter's two probes to the element's terminals were the wires connect. The element was fine. Then I checked the two sensors the same way. The sensor furtherest away from the element's terminals didn't have a constant signal so I assumed that that sensor was bad. Well, come to find out, one sensor is open and the other in closed... only when the temp. changes do they operate by opening and closing the current. By this time I had already ordered the part so it was too late. Surprisingly, the part came in 2 days. I ordered it Sunday night and i figured it would be sent out Monday but it was already in the air Monday morning... Great service! I replaced both sensors and the dryer works like it did when I first got it.

Used the trouble shooting tips provided as a guide and a multimeter to test and find the defective part. Testing indicated no continuity thru the high limit thermostat. I ordered the part and received it in 3 days. Had the repair done a full week before the repairman could even come to the house and saved well over $100 in repair costs and 2 weeks or longer of down time. Great website and service.