YKFED500ESS3 Whirlpool Range - Instructions

Video said to remove screws and lift stove top off, remove contacts and ground. My stove top was hinged and required me to lift and pivot stovetop up. The burners were anchored to the stove base not the top. I secured the topso that it would not drop down and proceeded with repair

Took the top and bottom plates off from the back of the stove. Removed the knob from the front, unscrewed the two screws holding it in. Then from the back side I unplugged the two wiring harnesses from the old switch, inserted the new one, plugged the harnesses back in and then put the screws back in the front to hold the new knob thing. Put knob back on, put the two plates baxk.on the back, plugged the stove back.in and turned the burner on. Success. I saved over $240 by doing this myself

Two screws to remove glass top. 2 connectors to remove. Removed glass top and put it upside down. Remove 4 wires and 2 Phillips screws. Reverse steps.

Took the back panels off the control console. Unplugged the wires from the failed switch. Removed the knob. Unscrewed the mounting screws from the front. Removed and replaced the switch. Replaced mounting screws, knob, and wires. Replaced back panel covers. Element now works!

Ordering the part online was easy. It arrived in a timely manner. I found a terrific video online showing how to install the terminal. It was so easy. Thank you for the great instructional video.

Pop old one out and new one in

Removed the small metal panel covering the main power terminal in back of the electric range. Removed the nuts holding the red, white and black electrical wires from the range using the appropriate socket (there will be two nuts on each bolt end). Removed the two screws holding the main power terminal block with appropriate screw driver. Connect the new main power terminal block to the range using the two screws. Reconnect the red, black and white electrical wires coming from the range using one nut for each wire. IMPORTANT: do no over tighten the nuts because the bolts could snap. Reconnect the pigtail and secure the small metal panel covering the main power panel.

replaced light socket but did not repair problem. must have burned the motherboard.


pleased with service from your company.

Unplug power cord, remove wires from block. take 2 screws out. replace with new block about 15 mins. Done

Turned off CB for the oven,Remove the oven from the cabinet , remove the back of the oven, replaced the light Assembly. turned on CB for the oven, tested the light. and truned off the CB and replace the back and reinstalled the oven in the cabinet.

ordered new broiler pan

Removed stove from slot in wall. Bent rear left leg would not unscrew due to bent metal bracket. Used hacksaw to cut out leg, then straightened metal bracket with small hammer and was able to screw new leg in and adjust height by using level on stove before reinserting stove its slot. Recheck level after pushing back in place and adjust front legs if necessary. If not for bent metal receiving bracket, would have taken much less time. Still easy tho. R'cvd part in two days. Very quick.

This is a no brainer. I am only doing this because you asked. Pull out the stove, tilt it back, remove broken leg, install new leg.

Removed two screws on sensor in the oven. Pulled out stove and after unplugging same removed the back panel. Sensor has an electric connection on the rear of the oven with a connection that is easily separated. Threaded new sensor electrical connection through inside of oven and connected on the back of stove. Pushed insulation back around the wire were in goes through to the oven. Replaced back on stove and screwed in two screws which hold sensor inside the oven. Replaced back cover on stove, plugged it in and pushed it back in place. Did the trick for me..

I went to the source of power on the stove and noticed one of the terminals had come loose from the terminal block and had shorted out against the cover of the terminal junction. After prying the loose terminal off cover I ordered new terminal block and received it the 2nd day. I removed the old terminal block and replaced the part in about 10 minutes..Thank you Parts Select for your easy to find diagrams and quick delivery.