YKERS205TS4 KitchenAid Range - Instructions

I trouble shot and traced out to electrical short in face panel and found burnt wires. I've been a licensed electrician for years and it takes alot of comon sense to trouble shoot and find problem. I found schetch-matic of appliance and searched computor and found partselect.com and tried it. It wasnt no time and the part was at my door. Thank you partselect and i would use them again in the future. billy

I received my glass panel realy quick from Part Select. It was an eansy job to install the new pane.
It took less than an hour. Thanks for Your prompt service.

Two screws to remove glass top. 2 connectors to remove. Removed glass top and put it upside down. Remove 4 wires and 2 Phillips screws. Reverse steps.

I followed the instructions as provided. When I finished I noticed the switch was 1/4 turn out from the off position mark on the stove. So I pulled the stove back out and took the back panel off again pulled the knobs back off took out the screws that held the switches in place and rotated the switch 1/4 turn counter clockwise. Then I replaced all the screws and knobs . Then I replaced the panel and shoved the stove back in place. One of the burners was an eight inch and the switch doesn't work as well as it could. However there was not a direct replacement for the eight inch burner.

The old part, including lightbulb and socket, had corroded into place, and the glass light cover was stuck to the socket. I used a dead blow hammer and a dowel just under the diameter of the hole to tap on the back side of the socket to loosen it and get it out. The metal tabs on the old socket were folded back to make it fit better (?), which made it harder to remove. Lots of muscling of the part to get it out. Easy to install new part once old one was out of the way. An experienced person would have removed the old part and installed the new in no time.

Put the back of stove on blocks of wood to get high enough to screw the new leg in.

Replaced the oven light with a new one but it burnt out as soon as I turned it on. Therefore I decided a new socket may help.

My whirlpool apparently has the old style socket which is pictured in partselect part #PS12584564. The old style socket has to two metal arms that retain it against the metal reflector.

The part that will come (#PS12584564) however is the new style that whirlpool has changed to, apparently. It is not as pictured. The socket and the reflector have different retention devices.

I used screw drivers to bend the two metal arms away to release the socket. Then I had to use allen wrenches to bend the reflector's retention tabs away.

Once I had the old socket, reflector, and lens replaced I just followed the video on partselect for part #PS12584564

Video said to remove screws and lift stove top off, remove contacts and ground. My stove top was hinged and required me to lift and pivot stovetop up. The burners were anchored to the stove base not the top. I secured the topso that it would not drop down and proceeded with repair

very easy watched the howto you gave

Ordered new element from PartSelect. It arrived shortly. It did not match the original. Guy at appliance store explained how I could connect the wires on the new one. It still did not fix the problem. A repair man tried for 2.5 hours to fix it with no success. Now I will return the replacement element in the return envelope provided.

Remove door
Remove front cover of door
Remove hinge screws
Put back together.

After removing element cover off with Phillips screw driver, found a little screw in bottom of oven. Couldn't find where that came from. Removed two screws from element bracket from floor of oven and one holding in the back wall. Most difficult was pulling the old element out of the electrical clamps and hoping the wire would not pop back into the insulation/ and replacing with the new bracket. That is where my hemostat came handy as pliers were too big and the hemostats stabilized the connection without it popping back into the oven. What was really astonishing was the new element and floor bracket DID NOT line up with the screw holes in the bottom of the oven. Could not adjust/move bracket as some of the element was "clawed?" on the bracket and feared I would damage it. Thus I now have two extra screws along with the one found on floor of the oven. Replaced cover and it currently heats nicely.

Very Simple, I recommend pulling the old gasket in sections, and popping the new gasket metal holders in the holes as you go. You can't mess it up. For the ends, I tucked them in using a pair of needle nose pliers, but any small slender tool, such as a thin screwdriver, will work.

It was alittle difficult at 1st to remove the clips that held in the socket. But once out everything went smoothly.

Pop old one out and new one in