WRT318FMDB06 Whirlpool Refrigerator - Instructions

The first thing to know on this model is that the handles for the refrigerator and the freezer are identical parts. It is the plastic piece at the end of the handle that breaks. Unfortunately, they only sell the complete handle, which is a shame as it is expensive. To remove the broken Freezer Handle, use a small allen wrench to loosen the bolt on the side. The handle should then slide off easily. You may then remove the two screws at the bottom. Slide the new handle into place, and tighten the screws at the bottom first. This will ensure the handle is properly located. Then tighten the allen bolt on the sidewhile holding the handle agains the face of the freezer.

I bought this refrigerator from a big box store w/o seeing the actual model, but was told the one I was buying was exactly the same only w/o handles sticking out. Not so. This model has no full-size freezer shelf even tho there are slots on both sides of the freezer for a full-size shelf. Whirlpool was no help, telling me I'd undo the warranty if I tried to put in a shelf that wasn't for that freezer, but I investigated & found the frig I originally saw, got its full-size freezer shelf model number, & voila! I'm now a happy camper with a better organized freezer. Freezer shelf fit perfectly, came intact due to being well-packed for shipment. Easy to install-just slid it into the shelf track slots.

First, made sure new fan worked then Placed back in bracket with bushings-only goes in one way, pushed fan back on. screwed bracket to back of freezer and ran the wires to their original place, plugged in the two plugs, put the back piece up attaching ground and pulling ice maker plug thru, screwed back on. Plugged in ice maker, mounted ice maker on freezer wall. Plugged it in. Exact reversal of how it was removed. Not a lot parts to get confused.

Took the refrigerator shelf out. Slid the broken part off the rim on the shelf. Placed the new one on the rim. Remplced the shelf in the refrigerator. Done!

Removed shelf, removed shelf frame and installed new one.

Removed door and replaced bushing bracket was ok.

Using a screwdriver

The problem with the replacement part is that it didn't fit cleanly and doesn't slide well with the existing drawer.
We were disappointed.

Unplug refrigerator.
Pry switch out with putty knife
Remove two wires from switch
Attach wires to new switch
Push new switch into slot

removed old and installed new compartment door by hand.

****Make are you order Capacitor & Starter relay too (we ordered separtely so had to pay shipping twice)**** Super easy just open access panel on back near compressor and remove retention clip with fingers, remove & replace both capacitor & starter, put clip and access panel back on, plug in and allow 8 hours to cool! Works like new again! Hope it goes another 10 years

I first replaced the switch and had no results, I then ordered the Light Socket Kit, and because I had the experience of removing the panel to replace the switch, it took a few minutes to remove the two screws behind the panel, removing the temperature control knobs and then releasing the face plate which is secured by tabs at the bottom. The kit came with extra connectors in case they were needed, but they were not in my case and so I pulled off the wires, pushed the old socket out and the new one in. Attaching the wires to the correct pins, I screwed in the light bulb to be sure that the fix was correct and determining that, I replaced the screws that held the panel in place. Voila, I'm a happy camper who found some outdated jars in the back corners of the newly lighted shelves.

I took a chance and ordered a switch that is next to the top of the door. looked for how to remove it easily done in ten minutes works fine last long time.

Pried out old part with screwdriver. Unplugged. When new part came, just plugged it in and pushed the part into place.

use kitchen knife to pry out. replaced switch assemble and pressed back into place. Could not have done this with out help from previous customers. Thanks