All Installation Instructions for LG Washer WM3360HVCA

Dishwasher would not fill

Used Youtube to look for a set of repair instructions. From start to end 35 min.

The difficult part was getting the door back on. Only 1 Youtube video I watched stated Do not remove the 2 center screws at the top. Wish I had seen that video first.

Overall very easy to do.

Parts Used:

Water Inlet Valve - Hot

Jesse from CARNEGIE, PA
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Pliers

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Did not draw the water and did not finish its cycle

Remove where the water pumps are and remove the one that was damaged easily

Parts Used:

Washing Machine Drain Pump

saul from NEW YORK, NY
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Instructions on how to turn Clamp counter clockwise to get back on tube assembly

Watched videos but didn’t show the clamp had to be placed on counterclockwise

Parts Used:

Clamp Assembly

Timothy from SCOTTSBORO, AL
Difficulty Level:
A Bit Difficult
Total Repair Time:
More than 2 hours
Tools:
Pliers, Screw drivers

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Washer leaks

Could not do the repair. Partselect sent me the wrong parts even though I gave them the model number and the brand they sent me the wrong parts.

Parts Used:

Cap,Siphone

Softener Cap

Detergent Dispenser

Wane from OLATHE, KS
Difficulty Level:
Very Difficult
Total Repair Time:
More than 2 hours

3 of 6 people found this instruction helpful.

Was this instruction helpful to you?

washer would not run

replaced switch as shown in the video...Worked great

Parts Used:

Door Lock Assembly

kirk from WEST COLUMBIA, SC
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Noticed small tear in hose bellows and leak during reassembly

I already had the top of the washer open, from previous disassembly to clean the front loader seal, and when I ran a trial load, noticed a small 1/4" tear in the hose bellows that attaches to the drum.

Very simple repair, remove the existing hose by loosening the clamps, paying attention to their orientation. Install the existing hose clamps onto the new hose, install and tighten the hose clamps.

5 minute job, if the washer top is off (which is also simple).

Parts Used:

Washer Hose with Bellows

Ryan from HIGHLAND, UT
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

soap dispenser broke

just put new part in very simple only problem was shipping yall used fedex went to 4 states and one state twice they finally gave it to USPS so it took almost 9 days to get here

Parts Used:

Detergent Dispenser

Roger from LA CROSSE, VA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Washer was giving an error and not removing water/spinning

Followed instructions on YouTube link. Replaced the shock absorber and washer is working really well.

Parts Used:

Shock Absorber Kit

Magalys from WYOMING, MI
Difficulty Level:
Easy
Total Repair Time:
1- 2 hours
Tools:
Pliers, Screw drivers, Socket set, Wrench set

3 of 6 people found this instruction helpful.

Was this instruction helpful to you?

Could not remove one of the pins

Removed the front and rear covers ,the control panel , removed the shock absorber pins and shocks installed new shocks and reassembled

Parts Used:

Shock Absorber Kit

Leslie from ORLAND HILLS, IL
Difficulty Level:
A Bit Difficult
Total Repair Time:
1- 2 hours
Tools:
Pliers, Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Drum was making a very load grinding sound

I took the washer completely apart and ordered any parts that looked worn and put it back together. It’s working like new and will last for a few years

Parts Used:

Ball Bearing

willard from RIVERSIDE, CA
Difficulty Level:
Really Easy
Total Repair Time:
More than 2 hours
Tools:
Pliers, Screw drivers, Socket set

1 person found this instruction helpful.

Was this instruction helpful to you?

Water filling the basin

Water would fill the basin when the washer wasn't used. I followed the video created by this site to make the repair. The video gave me the confidence that I could successfully make the repair myself. The hardest part was physically moving my washer out of its corner to make the repair. The parts were plug and play. Awesome!!

Parts Used:

Inlet Valve Assembly

Water Inlet Valve - Hot

Chris from RIVERVIEW, FL
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers, Wrench (Adjustable)

1 person found this instruction helpful.

Was this instruction helpful to you?

Hot water inlet had leak, kept filling washer, when offw

When to utube typed in my problem, very easy fix

Parts Used:

Water Inlet Valve - Hot

Rudy from SAN DIEGO, CA
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Washer would not start, but if you disconnect it and plugged it in it started without pushing start button

It was easy to remove the rubber gasket to get at the door lock. Removing the door lock and replacing was simple enough, but getting the metal ring securing the gasket was cumbersome and challenging. This took most of the time.
However, after replacing the door lock it was obvious that this was not the problem. I had to remove the new part and replace the old one.
For future, it was the pob circuit board that was defective and had to replace it. Apparently this is not an uncommon problem as there are a number of UTube videos about this.This job was more involved and took me over an hour and resolved the issue.

Parts Used:

Door Lock Assembly

DENNIS from EAST MEADOW, NY
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Error code DE

Followed instruction from you tube. Removed gasket holder, then gasket by door switch assembly then replaced with new assembly!
I am a 63 woman and found this easy to do, with help from you tube guy.

Parts Used:

Door Lock Assembly