WM2233HU (ABBEEUS) LG Washer - Instructions

All I did was first of all and since it is so heavy I put 2 furniture sliders under the 2 front feat because I had to pull it out from where it was onto the carpet and the back feat I just sprayed some wd40 so the would slide on the tile floor. Then I took the top off by removing 2 bottom screws and pulled the lid back and up and there wa ... Read more s the cold valve. Next I pulled the electric tabs off. Don’t worry they go on the same way they were on. Do not at this time remove the screws on the valve until you pull each off one at a time and place one at a time back on the new valve. Then remove the screws and the old valve and put the screws back on for new valve and you are done. Replace cold water hose turn on water check if no leaks replace lid, you are as if new once again. Good luck. Cost for all that is around $50

Followed video provided by this site. Very install, less than 30 minutes.

After I watched the repair video for the part, it was a snap. It went exactly as the video described the steps. Hardest part was moving the washer to get behind it.

Replaced cold water inlet. Removed 4 water lines and 5 wires put new part in and reinstalled lines and wires

Watched the easy video instructions on the product page and did the same on our machine - pop off the top, unscrew the plate from the front of the door inset. Its a little challenging to unplug the old lock assembly because it is a tight fit and not enough room for two hands to fit to provide a bit more leverage when pulling the power li ... Read more nes out, but once its out it is easy to install the new one and reattach the strike plate frame and top of the washer. Plugged back in and we were back in business. This $50 part ended up saving us at least $300 in repair fees to get it working again.

Incredibly fast shipping - arrived in less than 2 days - which was really helpful as we were unable to use the washing machine until we were able to get this fixed. Excellent pricing as well. Couldn't be happier I found this site and the product I needed so easily.

I looked at the video that is on the partselect.com website. The person that I talked to from the website was very knowledgeable about the problem with my washer and he gave me the part number to type in the search box of the website. When I typed the part number in the search box the part showed up and the installation video showed up al ... Read more so. The video is an excellent video. It shows exactly how to do it. I also downloaded the operator manual from the website to look up what the error code meant.

It was giving me a code got on YouTube it gave the code after that bought a new pump and fix done

I set my iPad on the exposed washing machine drum, was exposed after removing top as explained in video, and put on the ‘ how to do video it’. It was so easy for this 78-year-old brain, that I am very pleased with myself. Also would like to thank whoever I talked to, Chris, when I ordered this part from this company, Chris was very helpfu ... Read more l and took time with me. So this ‘do it yourself person’, and I’m really not a do it yourself person, WILL certainly be looking into other do it yourself fixers. Thank you again.

Removed the front and rear covers ,the control panel , removed the shock absorber pins and shocks installed new shocks and reassembled

I removed the top of the washer, pried the front control panel off (pull a couple of electrical connecters or just rest it on something), separated the tub sleeve from the front panel and then removed the front panel (two screws). To remove the pump - just remove a couple of hoses, two wires and slide it out of the clip below. Reverse the ... Read more process to install. A little daunting if you haven't done something like this before, but easily do-able once you get past your fears. A service call would cost much more than the $60.00 it took to get the part to my front door. This worked out really great - my wash smells fresh once again and my wife has moved on to the next project on her honey-do list!

Watch the videos on u-tube. I used the video where they did not take the top and front of the machine off. Make sure you get the spring pliers because they really do help

I tipped the right side of the washer up 9.5 inches using two 2x4s and I was able to remove and replace the old hose with the tools described.

Watched video on U-Tube , unplug power cord, turn off water, take top off washing machine, remove water hoses, unscrew parts, remove hoses with pliers, install replacement parts, put all back together. Does not leak any more !

The repair went good but time consuming. I replaced both inner and outer tub bearings along with the tub seal. I removed top by removing two screws in back then pulling back slighty then lifting up. I removed soap tray by pressing down tab and pulling out. Loosened soap dispenser and folded back on top. I removed control panel then front ... Read more door panel. Remove back panel. Remove motor and shocks and hanging springs which there are two. Disconnect the hoses attached to tub then pull the tub. Remove screws holding the tub halves together. Use punch to remove bearings. NOTE: If you put the bearings in the freezer prior to installing, they go in much easier. I used the old bearing, set it on the new bearing then I tapped the old bearing so not to damage new bearings. I replaced the seal then put everything back together. Not difficult but time consuming.

I removed the tub. Thin included disassembling the washer and disconnecting various hoses electrical connectors to facilitate the removal of the tub from the machine.
Once removed, I separated the two halves of the tub and removed the metal basket to gain access to the bearings and seal.
Removal of the bearings was much harder ... Read more than expected as they were very difficult to drive out of their pressed in mounting.
I finally was able to remove the bearings and fabricated a press using a piece of all thread and two steel plates to install the new bearings and seal.
I would not attempt to do this again with the proper bearing pullers and an official press to install the bearings gently without beating the tub housing.
This repair I feel is beyond the scope of your average DIY. The bearings can be damaged easily without the specialized tools to install the components.