WM2233HU (ABBEEUS) LG Washer - Instructions

Figured out how to take off top of washer, look inside for problem, ordered new part, watched video how to replace part. All on line. $65.00 later and my 19 yr old washer is still working awesome.

I actually did the repair exactly as the video showed. If I would have had the part at the time of discovering the problem it would have been about a 45 minute repair from start to finish. Worst part of the whole fix was moving the heavy washer.

Followed the video supplied by this site and everything was as described!

The video from PartSelect showed removing the retaining ring from the rubber washer tub boot to then allow access the door lock located behind the boot for replacement. That ring can sometimes be a real pain to put back on. This can be avoided altogether!

It's much easier to access the door lock switch by removing the two re ... Read more taining screws on the top cover of the washer found in the back of the machine. Remove the top cover and you can then reach down to remove the wiring connector, unscrew the two phillips screws on the front of the door latch and remove the door lock. Put the new switch on in reverse order; plug in the connector, replace all screws and the top cover, and you are done! This method took than 10 minutes from start to finish.

Please note that the washer should be unplugged from power while working on any electrical component.

remove 2 screws from top panel - pull top panel back and lift off washer. reach down on front side and remove wire harness that is attached to door lock assembly. remove the 2 screws on front of door lock,remove and replace with new assembly. attach wire harness and then tighten assembly with the 2 screws. replace top of washer panel and ... Read more tighten with 2 screws.

2 hose clamps and a hose, easy! This would be a very common cause of leaks in washers due to all the movement inside.

removed top and front. heater is at the base of the tub. the nut compresses the rubber seal and may take some wiggling to remove the old one.

Do not pay a service company to come to your house to make this fix!!! If you have common sense, simple tools, a phone camera and some mini zip ties you can do this!

After watching a couple YouTube videos on installing a new motor I had the confidence to start the job. My biggest worry was I'd forget where a screw/part went s ... Read more o I took a lot of pictures as I disassembled. I also laid all the parts out on a table reflective of where they belonged on the machine. I learned washers aren't rocket science - YOU CAN DO THIS. The most difficult part of the fix was my washer was a different model so much of the caging was completely different than YouTube disassembly, but once I got into the machine it was fairly identical. Easily popped out the old, broken motor and inserted the new LG certified part. Reassembled in 1/2 the time of disassembly and my machine works like new:) Hoping to get another 10+ years out of this washer.

Thanks PartsSelect for the high quality certified LG part. Very nice quality and weight.

Remove door assembly from the hinge, unscrewed screw from the panel. Leave couple screws to hold Hinges. Remove the rubber seal but stretching to spring out, not having rt tool (long nose plier). Remove rubber partially close to the hinge. Remove the Hinges and replaced it, then reverse putting together back. Use small screw driver to put ... Read more spring tensioner back. Reinstall frame door to hinge, double check everything.

ridiculously easy. removed the door gasket ring clamp. separated the gasket from the face. unscrewed the lock, removed the wire(gently). replaced the wire on the new lock. replaced the lock. replaced door gasket and ring clamp. washed clothes. Note- I had called a repair service and was given a $360 estimate in addition to the $130 dollar ... Read more service charge. All total- $50 dollar part(with shipping), less than 45 min total time and I'm no mechanic!

followed video exactly and it worked perfectly

Unpluged -shut off water removed 2 screws on lid,removed lid took 2 screws out holding part on swapped the hoses out and pluged wires in.

1 tilt washer back
2 remove cover plate screw from front of drain filter access panel.
3 Remove cover plate and remove 2 more mounting screws .
4 go below washer and pull down sliding clip and move pump assembly back.
5 remove wires and 3 mounting screws around pump housing
6 Swap pump and re-attch wires

It went great. First of all, thank you Part Select for the video on how to do this myself. My home warranty company was giving me a hard time. Blah, blah, blah. A mechanic friend of mine referred me to this site. Within minutes I found the part I need and a GREAT!!!! price. Ordered it, got it super fast, fixed it my self and my second han ... Read more d washer is no longer peeing all over the floor. Very very happy. I will definitely be a repeat customer, hopefully not anytime soon.
Thank you again for an amazing experience.

WATCHED VIDEO PROVIDED BY PART SELECT, AND FOLLOWED INSTRUCTIONS. VERY SIMPLE REPAIR.