WM1375HW LG Washer - Instructions

Follow the LG washer video.

E. Z. hardest part (which isn't hard) was moving the appliance to reach the back, then putting the appliance back into place. the actual repair (swapping out valve) took less time than that to do.

Removed top panal found broken parts and pieces, replaced spring and plastic spring holder. Straightened out and reattached drum front boot.

you tube it , not to hard to install

I youtube searched this problem and found a video from partselect. I watched the video, purchased the part, and followed the video instruction step by step to repair the washer. Part with tax and shipping was $52.

1 tilt washer back
2 remove cover plate screw from front of drain filter access panel.
3 Remove cover plate and remove 2 more mounting screws .
4 go below washer and pull down sliding clip and move pump assembly back.
5 remove wires and 3 mounting screws around pump housing
6 Swap pump and re-attch wires

Remove where the water pumps are and remove the one that was damaged easily

The spider repair and the tub seal replacement are fairly complicated, and time-consuming, but manageable with patience. I viewed the youtube video that showed the process, which gave me confidence. It entails disassembling the machine and removing quite a few major pieces. Take care with the numerous screws and bolts, and be patient and you can be successful. Plan a lot of time for all the steps.
The hardest part is putting the door bellows back on.

Do not pay a service company to come to your house to make this fix!!! If you have common sense, simple tools, a phone camera and some mini zip ties you can do this!

After watching a couple YouTube videos on installing a new motor I had the confidence to start the job. My biggest worry was I'd forget where a screw/part went so I took a lot of pictures as I disassembled. I also laid all the parts out on a table reflective of where they belonged on the machine. I learned washers aren't rocket science - YOU CAN DO THIS. The most difficult part of the fix was my washer was a different model so much of the caging was completely different than YouTube disassembly, but once I got into the machine it was fairly identical. Easily popped out the old, broken motor and inserted the new LG certified part. Reassembled in 1/2 the time of disassembly and my machine works like new:) Hoping to get another 10+ years out of this washer.

Thanks PartsSelect for the high quality certified LG part. Very nice quality and weight.

It went great. First of all, thank you Part Select for the video on how to do this myself. My home warranty company was giving me a hard time. Blah, blah, blah. A mechanic friend of mine referred me to this site. Within minutes I found the part I need and a GREAT!!!! price. Ordered it, got it super fast, fixed it my self and my second hand washer is no longer peeing all over the floor. Very very happy. I will definitely be a repeat customer, hopefully not anytime soon.
Thank you again for an amazing experience.

Used Youtube to look for a set of repair instructions. From start to end 35 min.

The difficult part was getting the door back on. Only 1 Youtube video I watched stated Do not remove the 2 center screws at the top. Wish I had seen that video first.

Overall very easy to do.

I followed the video. Everything worked exactly as described. i ran a quick cycle and everything seemed to be fine. Started a wash and the machine was going fine but stopped, and wouldn't drain. I thought that maybe it might be the Rotor Position Sensor assembly, which I had already purchased just in case.But first i drained the machine and checked out the pump filter. Plugged solid. I'm guessing when the pump went there must have been a lot of lint and debris in the machine. something you might want to check out, after that repair. Thanks. you guys saved me a couple of hundred dollars

Turn off circuit breaker. Turn off water at shutoff valve usually located under sink. Disconnect water line from dishwasher. Disconnect wires for the power feed from cord, Marked corresponding wires upon removal for re-installation. Remove 2 mounting screws that secure dishwasher to counter. Slide dishwasher out from counter and turn upside down. Use a blanket to prevent scratching of surfaces. Locate component on the back portion of the dishwasher. Unplug 2 wiring harnesses. My part was held on by 2 phillip screws. One in front, the other in the back along the leg bracket support. Once removed, reverse the order of removal. The i a You Tube video you can locate fr this removal. They said that you needed to release a clip to get the part out. Mine had a screw holding it on the back side. This difference cause about an extra 1/2 hour before I was able to figure out that there was NO clip that was being shown on the video. After that, The replacement went smoothly and we were having the dishes washed later that day.

When to utube typed in my problem, very easy fix

Replaced cold water inlet. Removed 4 water lines and 5 wires put new part in and reinstalled lines and wires