WFW95HEDC0 Whirlpool Washer - Instructions

Took sometime to figure out the problem. A little difficult to replace part partly due to the drain pump with filter’s location in the washer. Mine is on its lower right rear. It’s reachable and yet difficult. Good luck!

Disconnect electrical plug. Remove rear panel from washer. Remove drain hose. Open filter on pump unit to drain water from washer ( use a catch pan to catch water) remove drain hose from drain pump unit. Remove electrical connector. Remove 4 mounting bolts. Remove drain pump assembly. Install new pump in reverse order. Once washer is asse ... Read more mbled. Pour about a quart of washer into the drum so as not to run the drain pump dry. Enjoy your repaired washer

The end of the strike had broken off, and the pictures did not clearly show there was a cross-member at the end of the strike. That crossmember is what broke on the old strike. The strike has only two screws, both requiring a Torx bit (#20, I believe). Unscrew both screws to remove the strike plate. It was a little difficult to get out - ... Read more it has a curved top to lock into the top slot, but the bottom slides slightly down into another slot. There isn't a lot of room in the opening to slide the strike up and down and get it out. Putting the new strike on is easier - ensure the curved end fits into the slot at the top and slide it up just a bit, push the bottom of the strike plate in, then let it drop right into place, and reinsert the screws. The only problem I had was the strike's holes for the screws are slotted horizontally, so the strike can be positioned across almost 3/8". The latch would not engage the strike the first time, so I had to loosen the screws and reposition the strike a bit. This time it latched, but the fit wasn't quite right, so I adjusted it again to get it where I needed it.

Desarme la puerta y coloque la nueva con mucha facilidad, nunca reparé un electrodoméstico antes de este, seguí el diagrama que encontré en el sitio para elegir la pieza que se rompio

I didn’t know at the time that they weren’t gonna send me glass, they sent me plastic as a replacement. However the notch didn’t line up in the door to make sure it was in the right position so because it was plastic I was able to cut the notch out with a multi tool and made it work. I’ve been doing laundry all week and there’s no proble ... Read more ms

!!!! Unplug washer and let sit for about 15 minutes before performing any repairs!!!! Remove back cover with 1/4 inch nut driver. Locate drain filter under drum and slowly remove cap to drain(it will help to catch the water that drains out with either a shallow bucket or a wet/dry shop vac). Disconnect single electrical connector on pump. ... Read more Locate and remove four mounting screws with 1/4 inch socket and ratchet. Remove pump and remove as much debris as possible. Install new pump with light amount of dish soap or other lubricant on o-ring seal. Tighten mounting screws. Connect electrical connector. Reinstall back cover.

I followed your repair video explicitly, simple fix. However, one should
be careful when disconnecting the two prong electrical connector from
the heat sensor. the two black wires can pull free easily. In that case, the
rear of the female plastic wired connector must be extracted to allow the two black wires to be "pushed" ... Read more into the narrow slot which displaces the
wire insulation and allows for a good electrical connection. If a punch tool is not available a pair of needle nose pliers works. Also, observe
the orientation slots on both the male andfemale connectors - they
connect one way only! I set the washer on it's face while effecting this
repair to better see what I was doing (eyesight not as good as it used to be). Thanks for the timely support!

I am still waiting for the correct part to arrive, I was sent a part but it was the wrong part, the wrong part number and it was nothing that would work on a washing machine. I think someone else ended up with my part and I got theirs.

1 Pull the machine away from the wall.
2 Unplug the machine.
3 Remove three screws in the back on the machine that secure the top
4 Remove the top
5 Remove the water lines that are connected to dispenser
6 Remove the Detergent tray
7 Remove one 1/4-inch screw that secures dispenser to the washer brace
8 ... Read more Remove two torques tip screws from the front of the dispenser
9 Remove the outer ring securing the washer seal
10 Disconnect the rub hose connected at the front of the dispenser at the bottom
11 Reinstall the New Dispenser in reverse order
12 Test for leaks

Took door off with a Phillips screwdriver went to hardware store with door so he could match up the 6pt screwdrivers that were needed.
No more then 1 hour to do.

Replace front legs. Very easy fix.

Since I have All Whirlpool appliances in the home, the only one not a Whirlpool was a counter top dishwasher that looks exactly like it could be a Whirlpool and so not to be the odd unit out, I labeled it with with a Whirlpool logo nameplate on the face of the door. Now everything matches perfectly and all in the same exact color white t ... Read more oo.

Just measured and marked where the plate was to be located, cleaned that part of the surface, peeled the backing and carefully placed the logo name plate in place and pressed it on. Voila. Done and looks original as well. Call me the big, deep fakearooski.

Unplug appliance. Remove the back panel with the 1/4” nut driver and cordless drill. The pump is located as you face the back of the machine on the bottom. Remove four screws that hold pump in. Reverse the process and install new pump. Check the filter and clean out the housing.
Reinstall back panel and plug back in. Run a test load ... Read more (no clothes) and test drain.

Well, I am a 66 year old Grandma. I had to take off the entire back panel... no big deal ... then make sure to remember how the hose attaches to the bottom of the machine. Taking the clamp off with whimpy pliers was a little difficult due to the location. The most difficult part was laying on the floor and trying to use the stupid plie ... Read more rs that kept slipping off the clamp and try to shove the new hose on in the correct position. I just didn't have the grip power and manuverability to grab ... squeeze ... push the internal hose at the same time. I finally got it attached after 33 minutes. The rest of the hose attached litterally in a snap. Replaced the back panel and good to go!

The repair was simple as you can imagine. Thought I could buy these legs at any big box store or at least at the local hardware store. No such luck. Partselect had the right product---easy to order and easy to install. Things around here are great.