WFW9400SW02 Whirlpool Washer - Instructions

Water was slowly filling the wash tub and spilling out front of machine. Cause was the water inlet valve solenoid was not fully closing.

Turn off water to the machine
Unplug machine
Pull machine away from the wall
Remove the water inlet hoses.
At the back-top of the machine remove the three screws holding the top on.
Lift up top from the rear and remove it.
Disconnect the hose connected to the water inlet valve.
On the outside of the back panel remove the screw holding the water inlet valve.
Remove the water inlet valve.
Reverse the process to install the new valve

NOTE: in my case the hold in the back panel did not line up with the hole in the new water inlet valve. I drilled another hole.

the tabs were to big on the replacement and the customer representitive said he was unable to help me.

discouraged

I will never buy parts from this site again

Remove three screws on bottom panel lift up and remove panel.The water pump in right in front. One screw holds it in place and the input and output hoses are on the back side.The hose clamps are a little hard to take off I found that before taking the one screw off the pump remove these two lines.Putting the pump back in secure the pump with the one screw. The output line is easy the intake line can be a bit of a more work to get it on because the rubber is so thin.Getting this hose and clamp was tough. Most of all use a wet vac to remove water in washer and vac out the line to drain doing this will be water free during replacing water pump.Run a cycle to make sure the lins do not leak. The other is the people that has posted this replacement are very good

Factory hose clamps were awkward to maneuver. I used automotive radiator hose clamps instead. They worked great.

I did follow step by step your YouTube video. I’m a woman. There was nothing heavy in the process. You have to be careful that’s it. Thank you for the instructions. I fixed it with the YouTube tutorial you provided. Really nice from you people.

Shocks are the #1 recommendation for this problem, but they were not the solution. The problem turned out to be broken weld in the stainless tub. Three of the shocks can be replaced from the front, the one under the motor can only be accessed from the back of the machine, which means it has to be pulled out away from the wall. Taking the old ones out is kind of a pain, they don't twist off easily and there is little room to use tool. Putting the new ones in is easy, they just twist into place.

2 clamps and its off, problem is if you have average size hands you will struggle in getting the back clamp on and off.

First I removed the retainer ring that holds the outside bellows on the frame of the front washer.
I then pushed the bellows inside of the drum of the washing machine in-order to get to the clamp that holds the bellows on the inside of the drum. To pull the clump I had to use a stubby screwdriver and socket drive to loosen the clamp. Once the clamp is loosen I was able to pull the bellows off, of the drum and out of the washing machine. Installation was the reverse of removal.

I purchased a new bellows from this site I followed their instructions. Just tricky getting the inner clamp on aligned and tightened.

Pull spring wire on front. Remove large hose lamp at tub. Reinstall in reverse order.

replaced actuator switch. It did not fix the problem. Replaced actuator arm, and fixed. Needed the switch because gears were stripped. Needed the arm because it seems over time, the arm straightened, thereby increasing its length so that the rotation of the switch bound up during its cycle.

It was fast and pretty easy to do.

New baffles would not fit. PartSelect very helpful to get refund.

New baffles should just slide in but did not. Measuring slots and
connection points on new baffles appear to be a difference preventing
connection.

Did the repair just like the video on your website. Was really easy.

I am a 63 yr old woman. I was able to remove the washer door, take off the broken hinge, install the new hinge, and place it back on the front of the washer in less than 15 minutes! It is a front load washer and designed for one person to do this. I YouTubed a less that 2-minute video first. The hinge fit perfectly!