WFW9400SW01 Whirlpool Washer - Instructions

Of course the machine was not plugged in & water valves where off. I took water hoses off. Then i took 3 screws off the back of lid & slid lid back & lifted it off. I then unplugged two wires going to valve. I then took water hose going to valve off. Last there is one bolt holding valve to machine & in the mechanic industry we call this bolt a star head, so it was a good thing I had this tool. So if you do this repair you will have to get this tool. This job is easy to do & Part Select was 100% on my order & shipping! I will order again when something brakes again !!! Thank's

Disconnect the hot and cold water supply hoses from the rear of the machine. Remove 3 screws in the rear that fasten the top cover. Slide the cover rearward and remove it. Disconnect the black outlet hose and unsnap the two electrical connectors from the water valve. Remove one screw that fastens the water valve to the rear panel. Slide the water valve away from the screw and remove it. Reverse this procedure to install the new valve.

I opened the top by taking four screws from the back and lifted the top. The part to be replaced was clearly in view. I opened the clamps on the hoses, pulled the hoses off, removed the wires, and reversed the process with the new part. The washer works great now! I ordered the part on a Friday, and it was delivered the next day, even though I didn't pay for overnight!

Disconnected the water supply lines. Removed four screws holding the top to back frame. Removed the top. Disconnected the electrical valve connections. Removed the valve set mounting screw. Removed the valve set and replaced. Reversed the steps above for installation.

I had replaced the flowmeter, but that didn't solve the problem, so I ordered the hot/cold solenoid fill part. Other than ONE screw that was unique -- the back retaining screws were nut driver screws, the one retaining screw was a torx which, of course, couldn't be seen unless you pulled the washer all the way out. Unscrewed that, unhooked the hose clamp with pliers and worried the hose off, removed the four electrical connections (which were TIGHT) and replaced the part. Turned on the water and was dismayed to get a d/l error code. After some colorful language learned from my drill sergeant 40 years ago, I realized that was "door lock" and closed the door tightly. Ran great and the Mrs. thinks I'm a hero.

It took less time to repair than it took to get new baffle out of the packing sleeve. Set it in drum and snapped it in place. Took about 5 seconds.

Placed baffle in drum over slots pushed down on it and slid it back to lock it in place. You will hear it click.

Easy peezy!! Next day delivery, as promised for parts that could not be found anywhere else. I placed the baffles in the washer and clicked them in using both hands one by one. I'm petite and weigh about 110 lbs. The total installation time was less than 2 mins. I was given a $200 quote just for installation but, spent less than $100 and installed myself. Thank you!! I will not wait so long and shop around next time. I'm going straight to partsect.com to save time and money. Although I have to buy new clothes now since my washer put holes in all my clothes. But, the problem is finally solved and I am so grateful.

Looked at how the old drain pump was installed, then removed it and installed the new one. It was a fairly simple fix. The only feedback were that the parts picture was a little confusing becuase the picture didnt really look like the actual part, so we were unsure if we were ordering the correct part.

Very limited access to the bellow clamp. Found it easier to first remove washer front panels (8 screws total), providing ready access to R&R the bellow. 40 minutes tops.

This was so easy to swap the parts out. The plastic hooks that hold the pieces inside our washer had just worn out. We put our washer and dryer through LOTS of use and I am amazed it has hold on this long! The broken piece just popped out and the new piece just snapped right in. Thank you for your speedy shipping and the great price.

After diagnosing codes noticed no drain replaced pump asm

I did not replace the pump body. I just removed the motor with the 3 screws. Put the new one on. This way I did not need to mess with the hose clamps.

The drum baffle came off. This website provided a diagram to make ordering the part easy. It was reasonbly priced and came in the mail very fast. I had it installed in my washer within 5 minutes. Excellent experience. Thank you.

replaced drain pump.Saved 200$