All Installation Instructions for Whirlpool Range WFG714HLAS1

Oven sensor was not regulating heat set for oven

Following your installation, the old part came out easily, with new part installing easily., oven heat is being regulated properly..with range pulled out for part replacement, got that area cleaned too

Parts Used:

Oven Sensor

Linda from SAINT CLOUD, MN
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers

3 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Oven Temp inaccurate

I watched the repair video on this site and another on YouTube before I started. The rear panel has a different shape and two additional screws on the bottom edge. The power clip was easy to manipulate.
This was an easy fix for a seventy year-old like me!

Parts Used:

Oven Sensor

David from BURNSVILLE, MN
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

3 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

the old gaskt was not linge dup well, the door was not closing well

pulled the old gasket, the new one fitted perfectly. No effort at all.
An instruction sheet would be a bonus. I wish you put instruction sheet in all parts OR a web link for video instructions. a web link would be great

Parts Used:

GASKT-DOOR

mohaemd from pittsburgh, PA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

6 of 12 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Replacing the bulb in the freezer side

Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.

Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.

Parts Used:

Light Bulb - 40W

Yafa (and David) from Bothell, WA
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver

5 of 10 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

oven not keeping correct temp and sometimes would not relight when temp went dropped.t

Slid oven out and took back shield off unplugged sensor took bracket screw out replaced sensor with new one.

Parts Used:

Oven Sensor

Gary from PLUM CITY, WI
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers

3 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Faulty ignitor

Remove bottom plate take screws and hex head nuts remove wire unscrew ingnitor reverse process with new ignitor very easy

Parts Used:

Oven Bake Igniter

Mark from HOLLAND, MI
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers, Socket set

3 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

temp sensor went oven not heating

the hardest part was moving stove to trplace part

Parts Used:

Oven Sensor

patrick from HUGHESTOWN, PA
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

3 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

No problems encountered

It was easy to remove the old oven door gasket. Just a little tug was all that was needed. Installing new gasket was just as simple as tucking in the gasket end into the hole at the bottom and pushing the clip in the corresponding hole.
TIP: roll the end of the gasket and feed into the hole then use a small tipped screw driver or the point of a needle nose plier to finish installing the ends into the hole at the bottom of the door opening.

Parts Used:

GASKT-DOOR

Scott from Troy, IL
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

One of the burner grates broke

Replaced the grate.

Parts Used:

Range Surface Burner Grate

Rob from GALENA, IL
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

3 of 5 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Oven not reaching temperature

Simple-pulled range away from wall, unplug from socket. Removed back panel unscrewed thermoses and replace. Put back panel back on plug in, tested temperature setting before sliding range back on place

Parts Used:

Oven Sensor

Marsha from Clermont, FL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Oven stopped heating, error message stated heating element

Very easy. Pulled the stove away from the wall. Used a screw driver to remove the two nuts to release the heat sensor, disconnected the wire, removed the sensor. Inserted the new sensor, plugged back into the circuit. put the two nuts back.
Beware, if the first time you put the oven on, if the error message comes back up (mine did) push the cancel/off button, wait a few minutes, put oven back on. System probably needed to reset. Mine worked perfectly after.

Parts Used:

Oven Sensor

Lana from WATERVILLE, ME
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

the oven temperature was not working right. I installed a new oven sensor. Works get now

Watch the video...

Parts Used:

Oven Sensor

Rosalind from APOLLO, PA
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

3 of 6 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Ignoter gave out

Opened oven... removed grates and bottom panel. Unbolted igniter has flange and end wire. Attached end wire to new igniter and reattached new igniter to gas flange. The rest in reverse and set oven and pressed start.

Parts Used:

Oven Bake Igniter

Michael from CHICAGO, IL
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Needed to replace over door gasket

Very Simple, I recommend pulling the old gasket in sections, and popping the new gasket metal holders in the holes as you go. You can't mess it up. For the ends, I tucked them in using a pair of needle nose pliers, but any small slender tool, such as a thin screwdriver, will work.

Parts Used:

GASKT-DOOR