WFE510S0AT0 Whirlpool Range - Instructions

Turned off power to range. Took back panel off to reveal all controls. Pulled off knob of bad control. Removed 2 screws from the front of the control. Pulled off wiring from back of old control. Took new control reversed procedure. Reinstalled back panel turned power on and tested new control. Total time about 20 minutes

Replaced the oven light with a new one but it burnt out as soon as I turned it on. Therefore I decided a new socket may help.

My whirlpool apparently has the old style socket which is pictured in partselect part #PS12584564. The old style socket has to two metal arms that retain it against the metal reflector.

The part that will come (#PS12584564) however is the new style that whirlpool has changed to, apparently. It is not as pictured. The socket and the reflector have different retention devices.

I used screw drivers to bend the two metal arms away to release the socket. Then I had to use allen wrenches to bend the reflector's retention tabs away.

Once I had the old socket, reflector, and lens replaced I just followed the video on partselect for part #PS12584564

very expensive to buy the part but just tighten the screw intot eh predefined place.

Watched the video and did as shown

It was alittle difficult at 1st to remove the clips that held in the socket. But once out everything went smoothly.

removed two screws to faceplate at rear of oven. Disconntected contact wires, installed bake element reconnected contact wires, attached faceplate turned on oven holy hell it works just saved some money on service call thanks!!!

Unplugged oven , removed screws ,pulled wires out, removed old element , just hooked wires up , screws .make sure it sits level plugged in. Works great

Our repair was extrodinarily easy. As my husband was taking out the old element and the oven was off, the element heated up and actually burned him. He readjusted it and it refused to heat again. We figured at that point that there must be a short, so we never even opened the box with the new element. A short time later we decided to use the top of the stove for soup and a small fire started in the oven. We turned off the braker at that point and ordered a new oven.

Video said to remove screws and lift stove top off, remove contacts and ground. My stove top was hinged and required me to lift and pivot stovetop up. The burners were anchored to the stove base not the top. I secured the topso that it would not drop down and proceeded with repair

very easy watched the howto you gave

1. Pull the stove away from the wall and unplug the stove from the 240 volt receptacle.
2. Remove the knob from the switch (it just pulls off).
3. Unscrew the top half of the back plate of the stove and removed (about eight or so screws).
4. Unscrew the two screws attaching the control switch in the front of the control panel (these were hidden by the control knob just removed).
5. Pull out the control switch and detach one at a time the two sets of wire connectors attached to the switch. In order not to confuse which plug goes where, attach each connector to the new switch as you remove them. (Note: the connectors may be quite tight to the original switch; do not pull on the wires but simply work each connector gently until it slides off. They will reattach to the new control switch much easier.)
6. Reinstall the new switch to the stove in reverse order of removal. Make sure that the control knob, when the switch is reattached, is in the off position pointing straight up.
7. Reattach the upper back plate of the stove. For safety's sake, do this before reconnecting the stove to power.
8. Plug in the stove and test to ensure that the switch is working properly.

Followed instructions on urine that you provided. Instructions were great.
Only problem had was the screw was hard to get loose on one due to oven usage from previous people but I got it after a bit and then fairly simple from there. Unplugged and plugged new element in. Works although seems to run a bit hotter than before.

After my husband replace it we noticed that our knob was worn to the point it would not turn on the new switch. I am sure the switch was o.k. so kept the old one and getting a knob to fix the issue.

I used the replacement video from the web site. The replacement went great.

Had an electrician to do the job for me.

Turn off 220 voltage, unplug and remove clips. replace it with new part. Check part before replacing the top of range, if it works, the electricity can be turned back on. Repair done.