WFE505W0HB1 Whirlpool Range - Instructions

took old one off and installed new one used electrical tape to hold glass from sliding.Unscrewed moulding and installed new one

removed 3 screws holding the strip and replaced with new strip

By hand screwdriver

Watched video & did just guy in video did. Very easy job & the burner works like new.

Pulled range out from wall, unplugged AC, unplugged infinite switch, plugged in new switch, broke off end of stem, plugged AC in put range back and tested.

Pleaae prepopulate the manufacturer and part i purchased. I fix a lot of appliances so cannot expend the effort to decipher this.

Be well.

Replaced the safety thermostat and disconnected the oven light.
Works great again...without the light

Repair is fairly easy. Turn off power source or unplug the range. Pull the range out to access the rear sheet metal panels; there's two of them, large upper and smaller lower one (that covers the A/C power connections). Remove the two screws in the bottom panel first and put it aside. Before removing the screws on the upper panel, take note of how the top vertical edge of the panel "tabs" are inserted underneath the stationary top of the range. Remove either five or six screws on each side of the panel and put it aside. Now the rear of the control board is accessible. All of its connectors are color-coded, although its best to shoot a pic of it before removing them. After removing all of the connectors, there's one mounting screw on each side of the board; remove them and pull out the board. Now, install the new control board, making sure all of the connectors are properly secured. Restore power to the range; make sure the problem is resolved (before reinstalling the rear panels) by entering the BAKE mode. Pre(heat) cycle begins to default 350-deg temp; should take 8-9 mins from a cold oven to reach 350-deg. If it passes the test, shut off power and reinstall rear panels beginning with the UPPER one, paying attention to the "tabs." Then install the lower panel, reapply power, slide the range back into its home base making sure the anti-tip bracket is properly engaged. That's it.

turner off circuit breakers for range, i rolled the range out from between counter tops so i could see the burner sw. using a flash light read all the numbers on the switch to my wife who wrote then down, knowing what the switch looked like i could find could find correct instruction video on parts select & check the switch numbers & ordered it. replacing- made myself a drawing of the wiring connections, replacing switch-power off, unscrewed mounting bracket, removed switch, removed ONE WIRE AT A TIME & CONNECTED IT TO SAME TERMINAL ON THE NEW SWITCH, remounted the switch & turner on circuit breakers

Simple-pulled range away from wall, unplug from socket. Removed back panel unscrewed thermoses and replace. Put back panel back on plug in, tested temperature setting before sliding range back on place

Replaced switch. Works right now.

After identifying the part and taking delivery of it, I opened the breaker for the unit and then removed the range top by taking out 2 Phillips screws and lifting the part away from the hinges in the back. The element was attached with only 2 spring loaded clips which I then removed, noting the numbered position of each. I then photographed the wiring (x4) from several angles and removed each of them. I attached the clips to the new element and reconnected the wiring to the main heating element and the sensor per the photographs. The element was then re-positioned into its mounting slots, the range cover was reattached with the screws and the unit tested once power was restored.

Very easy. Pulled the stove away from the wall. Used a screw driver to remove the two nuts to release the heat sensor, disconnected the wire, removed the sensor. Inserted the new sensor, plugged back into the circuit. put the two nuts back.
Beware, if the first time you put the oven on, if the error message comes back up (mine did) push the cancel/off button, wait a few minutes, put oven back on. System probably needed to reset. Mine worked perfectly after.

Watch the video...

took out the drawer by removing two fillips head screws, four more screws removed the drawer front. Two plastic push pins and the front panel was off. Put the new panel on secured it with the pins, attached it back on the drawer front, put in the screws and slid the drawer back in the stove, put the two screws back in, done deal!