All Installation Instructions for Whirlpool Range WFC310S0EW0

The hinge was mounted on the right . The screw to remove it got it's square head chewed up because of using the wrong ssize driver

I left the old broken hinge in place, & put the new hinge on the left side.

Parts Used:

Door Hinge - Active With Spring

Howard from CROWNSVILLE, MD
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers

3 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

The door wouldn't close.

Watched a video on you tube!
When I ordered the hinge it was recomended to replace both hinges. so I ordered two hinges not knowing that one of the hinges didn't have a spring. I ended up with an extra hinge.

Parts Used:

Door Hinge - Active With Spring

Dorothy from PORT ST LUCIE, FL
Difficulty Level:
A Bit Difficult
Total Repair Time:
More than 2 hours
Tools:
Screw drivers

3 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Oven sensor was not regulating heat set for oven

Following your installation, the old part came out easily, with new part installing easily., oven heat is being regulated properly..with range pulled out for part replacement, got that area cleaned too

Parts Used:

Oven Sensor

Linda from SAINT CLOUD, MN
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers

3 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

large right front burner wasn't going on

turner off circuit breakers for range, i rolled the range out from between counter tops so i could see the burner sw. using a flash light read all the numbers on the switch to my wife who wrote then down, knowing what the switch looked like i could find could find correct instruction video on parts select & check the switch numbers & ordered it. replacing- made myself a drawing of the wiring connections, replacing switch-power off, unscrewed mounting bracket, removed switch, removed ONE WIRE AT A TIME & CONNECTED IT TO SAME TERMINAL ON THE NEW SWITCH, remounted the switch & turner on circuit breakers

Parts Used:

Surface Burner Element Switch, Large Burner

RUSSELL from LEESBURG, FL
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers, Socket set

3 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Broiler element burned out

After doing a YouTube search. I successfully completed the repair by easily diagnosing the issue with the element.
I watched a video about 5 most common problems with whirlpool broiler elements.
The first being to inspect the element for damage. I found a small section that appeared to be rough and had a raised bump.
I decided to order a new element because the oven is older and it wouldn’t hurt to install a new one even if this wasn’t the issue.
Once the part arrived, which it did quickly, I followed the video instructions. It was easy and straight forward. I completed the task in under thirty minutes. It was very simple and I now have a functional broiler element.

Parts Used:

Broil Element

chris from HILTON HEAD, SC
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

3 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Broken spring hinge

the door came apart fairly easy getting it all back together was another story lining up glass and panels that have already been heated was fun but its back together and working fine.... It should be noted that I have a warranty for the stove but the hoops I had to jump thru and the time it would take for the tech to come it was easier to do it myself!!

Parts Used:

Door Hinge - Active With Spring

Ralph from TEATICKET, MA
Difficulty Level:
Difficult
Total Repair Time:
1- 2 hours
Tools:
Screw drivers

3 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

bottom piece of range rusty

took old one off and installed new one used electrical tape to hold glass from sliding.Unscrewed moulding and installed new one

Parts Used:

Trim, Lower (White)

Bruno from LE ROY, NY
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

3 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

oven not keeping correct temp and sometimes would not relight when temp went dropped.t

Slid oven out and took back shield off unplugged sensor took bracket screw out replaced sensor with new one.

Parts Used:

Oven Sensor

Gary from PLUM CITY, WI
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers

3 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

temp sensor went oven not heating

the hardest part was moving stove to trplace part

Parts Used:

Oven Sensor

patrick from HUGHESTOWN, PA
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

3 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

i sat a tupperware bowl on a hot burner and it stuck to the burner so i had to replace it

just plugged it in!

Parts Used:

Surface Element - 6 Inch

judy from palatine, IL
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins

3 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

piece of cake. The pictures with the grid background on your website gave me ability to verify what I was purchasing.

This is the second use of Parts Select. First time was for another obscure part for an old microwave, which also worked out VERY well. Both appliances still in action.

Parts Used:

Chrome Drip Bowl - 8 inch

Drip Bowl - 6 Inch

George from Irving, TX
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

3 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Replacing the bulb in the freezer side

Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.

Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.

Parts Used: