This drum support roller is sold individually. Most dryers require two. The tri-rings are included. This is a drum support roller for a dryer. It is a genuine replacement part. The part includes the d...
This thermostat may differ in appearance, but functions the same as the original part. This part controls the temperature of the inside of the dryer drum and prevents the dryer from overheating.
If you notice that your dryer is noisy or will not tumble, you may need to replace the tri ring. This part is triangular, and is less than an inch in size. Tri rings can be found both on the idler pul...
This 18 ml bottle of white appliance touch-up paint is used to cover scratches or marks on your appliance. The white touch-up paint can be used on refrigerators, microwaves, ranges, clothes dryers, an...
The blower wheel is a squirrel cage type wheel whose purpose is to move the air through the room or appliance. The blower wheel spins on the motor shaft to blow air through the dryer drum and out through the exhaust.
Ask our experts a question about this model and we'll get back to you as soon as possible!
7 questions answered by our experts.
< Prev
1
2
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Mauro
February 13, 2020
Turn on everything. It also turns on the heat element but does not turn the drum
For model number WED6400SW1
Hello Mauro, Thank you for the question. If everything is working as normal but the drum will not tumble, we suggest checking the Belt, PartSelect Number PS11746376. We hope this helps.
The sensing light comes on and pf shows up after unplugging it....
For model number WED6400SW1
Hello Garry,
Thank you for your question. The "PF" error code means the dryer cycle was interrupted by a power failure, press and hold the START button to restart the dryer, and the error should go away. We hope this helps!
Was this helpful?
Thank you for voting!
Erik
January 19, 2020
This model was making a scrapping sound, now it won't start a cycle?
For model number WED6400SW1
Hello and thank you for writing.
Sounds very much like you have a faulty pulley or belt, there is a maintenance kit PS373087 available for this model. The kit includes the drum belt, drum support rollers, one idler pulley, four tri-rings, and one clip. We hope this helps. Please contact us anytime if you require further assistance.
Replaced thermostat and heat sensor still takes to Long to dry and can't adjust time for length of dry
For model number WED6400SW1
Hello Ron, Thank you for the question. We suggest testing the HI-Limit Thermostat and the Heat Element with a multimeter to check for the continuity. We hope this information helps!
After my dryer run for a little while it starts to screech, it does this for about 10 minutes then stops. Have any suggestions on what is making it do this?
For model number WED6400SW1
Hi Stacey, thank you for your inquiry. We would recommend checking the drum support roller, part number PS11752609, to get to the root of the problem. Good luck with this repair!
Grow a second set of hands. Always unplug any appliance. Remove lint screen. remove two screws (philips Head). I took a wooden shim lightly tapped w/hammer to pop front of dryer top free. Mine worked on hinges and just flipped back til it rested against the wall. Removed two 5/16 screws inside holding face on carefully raise face section off the support clips at either side on the bottom. Pull drum out (I have the large style drum commercial size [approx.). Clean the inside free of all lint (known to be fire hazard). Sling new belt around drum. Get newly grown set of hands to hold drum in place. Pinch belt to fit between tensioner, lift tensioner and place belt around motor pulley. Spin drum couple times to make certain belt isn't twisted. Reverse dismantle proccess to put back together. Replace all parts that come with kit, you'll feel better knowing you got a new dryer, almost.
After a few years of slamming the dryer door (at least that is what my husband says), the catch on the dryer door broke. Using pliers (I used needle nose) squeeze the outer edges of the catch together (vertically). With it compressed, it should slide out easily. My husband had jacked with ours prior to the repair, so the broken piece in the door was actually sideways and would not fit through the hole. Using a screwdriver, I pushed that piece into the door (it lives in the door somewhere now). I was then able to slide out the rest of the old catch. Compress the new catch and insert it into the hole in the door. Push it in until it clicks into place. DONE! Happy Drying!
couldn't get blower wheel off of the motor. really tight. rounded off the wheel's square hub while trying to hold it still as I turned the motor shaft out. No, I wasn't turning it the wrong way :) I ended up going to the back of the dryer and using the multimax to quickly cut the wheel away from the hub. I love that oscillating saw! Just for fun, I put the motor in a bench vise and got the wheel hub off (in pieces). VERY tight! Ordered new wheel, and the job was smooth sailing from there on. I am guessing that experienced repair people automatically order the motor and blower wheel at the same time(?) BTW both parts were perfect matches for the originals. Not surprised; this has always been my experience with partselect.com!
