WED6200SW0 Whirlpool Dryer - Instructions

this was very was very easy. But I deviated from the You Tube instructions. One to release the motor pulley. I needed to use 2 adjustable wrenches for a longer lever. I needed to use a hammer to help release pulley. Second to remove the dryer cable I needed to use a small screw driver to aid in the release. ---- the part from the company was a perfect fit.

we received the two heating element wires in 3 days and connected the heating element with no problem works great.

Pliers and screw driver to pop out the old door catch and pop in the new one. Saved $69.95 service charge for a tech to come to the home.

Followed simple instructions to replace two pulleys and belt. The Virtual Repairman helped me identify the cause in minutes. Took another 5 minutes to place the order and the part arrived two days later. Saved $125 at least. Thank you!

john

I was not able to find a video (or other specific instructions) that showed how to access the insides of this particular machine, but eventually figured out that all it takes is popping 2 clips, one on either side of the door by wedging a flathead screwdriver in the space between the top of the machine and the bottom piece that surrounds the door opening. The top then pivots up and can be moved back beyond vertical so that it hold itself in position.

After removing the dryer door, getting to the drum itself was not too difficult and only involves removing half a dozen small bolts. I was able to move the pieces off to the side without disconnecting any of the wiring. Without looking at the parts diagram I can't name any of the pieces involved, but there were only a couple. The drum can then be lifted right off its rollers.

The replacement felt for this dryer has to be fastened with adhesive, and I would recommend running the bead of glue around half of the drum, setting the new felt in place, letting it sit for a few minutes to let the glue set up, then repeating for the other half. I tried installing the entire piece of felt at once, but after getting about 3/4 of it on, pulling the remaining unattached felt taut to fit around the drum ended up removing the first part of the felt because the glue did not have time to set up. If you've ever changed a bicycle tire, you'll know about reaching that point where the tire doesn't seem big enough to fit around the rim, but it just needs to be muscled into place. Same idea here, but trying to muscle the felt over fresh glue while the just installed part comes loose is frustrating and in my case almost resulted in ruining the entire new felt strip. Once the felt is anchored it's easy to pull taut over the remaining part of the drum.

1 screw to replace.

Followed video instructions using flat scraper & pliers (easy).Tried to remove "SPARE" latch on other side of door. Even removed door myself (Easy).Tried for (45) minutes without success. Ordered part @ 11:30 pm. Replaced door easily by myself by leaving bottom screw for each hinge in place & replaced broken latch. Received new latch in (5) days. Removed broken latch without tools & replaced new latch in (15) seconds. Need help from any "Ladies" who can remove second latch so it is available for next replacement. This "Engineer" was too lazy to remove the screws around the door because he was going to "Follow the Video". Overall it was an "Easy Fix". Keep the 'Videos"coming.

Purchased the dryer maintenqance repair kit. Very simple to do. Easy to follow instructions. Took less than an hour. Everything I needed was in th kit. Did not have to run to home depot for anything.

Super easy to repair...I had to idea how to get started; but after watching the video from your site it was a breeze. Thanks for having "how to repair" videos on your site.

Repair kit came in 2 days..fantastic..thank you so much....with new rollers, belt and tension roller she works like new

(Always unplug dryer before making any repairs) I opened the dryer and checked the heating element. Making sure that the connection was good and nothing was damaged, I determined the problem was overheated wires. They melted and lots connection. I replaced them with the heating element wire connection kit. Easy to install and simple to get right. I cleaned the dryer again with a vaccum cleaner, removing all the lint, and checked the vents, making sure they were clear...I turned the breaker on (it was tripped when the dryer overheated)and everything worked great.

First, let me say the t videos are excellent. Check them out if you haven't already.

I came across the video on diagnosing the causes of odd dryer noises. After watching that, I decided that the issue was probably a drum roller.

I took a chance and ordered the maintenance kit to avoid having to take the dryer part to confirm the diagnosis and then put it back together again while waiting for the parts to arrive (BTW - the parts arrived within two days of my ordering them) .

Even if you know your issue is only the roller, I recommend getting the entire kit. It takes no extra time to replace the drive belt and the idler pulley while you have to dryer apart and I consider it good preventative maintenance.

Definitely watch the how-to video PartSelect provides on how to perform the repair using the maintenance kit. It's very clear and very helpful. I'm not sure I could have figured out how the belt fit through the idler pulley without it.

As video shows, the repair is pretty straightforward. As others have noted, you'll likely find a couple of dollars in change and a goodly layer of lint in the bottom of the cabinet. Have your shop back handy.

It seems kind of silly, but I found the hardest part of the whole repair was getting the front panel to slide onto the two bottom clips that support it.

One thing to watch out for are two small metal clips surrounding the screw holes at the top of the front panel. The nut screws that hold the panel in place screw into these, not the panel itself. After I struggled to get the panel in place I realized that in the process I had knocked the clips off and so had to remove the front panel again in order to retrieve the clips from the bottom of the cabinet. Minor frustration. And with all the practice I had the first time around, the panel went on much more easily the second time :-)

It was very gratifying to plug the dryer in, turn it on and have it run perfectly. Better yet, it impressed my wife.

new part came in a day or two. took part out of package and it easly snaped in place. very nice

Un plug or remove power before you start. First you would have to remove the rear panel of the dryer. All you need is a quarter inch nut driver. Then look at the bottom right side of the dryer. There you will see the heating duct. At the very bottom is where the element is. There are two screws on both sides( they will all be removed with a quarter inch nutdriver ). After you have removed the four screws holding the element on you will have to remove two wires from the elemet be sure that you mark them and dont mix them up. You will also have to remove the round temperature sensor because you will have to reinstall it on the new element. Then you get new element and reverse the order of my directions. Good luck and be safe ALL WAYS REMOVE POWER BEFORE WORKING ON ELECTRICAL APPLIANCES.

Pulled the dryer away from the wall took back cover off the dryer. Used volt/ohm meter to identify the bad element. Ordered the element it came in two days. 2 screws and 2 wires to plug in and we were back to drying cloths

thought the heating element was bad, once inside the element
looked good, tested continuity , tested good.
further test revealed I only had 110 volts at the wall outlet,traced problem to fuse blown in disconnect box under
the house.
Did not need the heating element.luckily parts select is taking the new element back since I did not use it.
Hope this review helps.