WD90280BD (ABWEEUS) LG Washer - Instructions

Unplug washer!!! 1. Remove retaining ring around rubber gasket with flat head screwdriver. Just slightly pry off and it will easily come off. 2. Just peel back rubber gasket on the side that the lock is on. 3. remove 2 screws from the front off the lock assembly. 4. gently reach in and lift the little plastic clip holding the wiring harness and lift straight off. If the clip is lifted it might be a little tight just use even steady pressure to pull off. 5. Reverse these instructions to replace. Note: replacing the retaining ring on the rubber is a pain. The spring has to be in the bottom. Using a couple of flathead screwdrivers you can wrangle it back in place after awhile. There is a tool that looks like a large reverse pliers that may make it easier. Anyway thats it, pretty easy. There is a youtube video that shows all of this.

took out the drain pump and replace with a new one

During my troubleshooting, I removed the bottom to access the drain pump. I had to cut some wire ties so that I could make removing the wires easier. After checking the pump and putting everything back together, I determined that the pump itself was bad. Pump impeller should not rotate freely! After receiving new part, I installed it relatively easy. I didn't have to remove the bottom since there was enough room through the access hole. Just make sure to make where wires go before removing old part.

1. Remove spring-loaded clamp assembly. 2. Partially pull out the large rubber gasket near the lock switch assembly to gain access to the lock switch assembly. 3. Unscrew two screws holding the lock switch assembly. Carefully separate the connector from the lock screw assembly and replace it with the new part. Reinstall in reverse sequence. Ensure that the electrical connector is fully seated unto the lock switch assembly and the connector latch is fully set against the lock switch body. Also make sure that the large rubber seal is fully seated around the door opening to prevent water leak. Restarted the washer and everything worked as before.

The machine was making a grinding noise instead of draining. I spoke with the LG rep on the 800 line and was told to call a repair man. The Parts select diagram helped me to identify the part I needed. It was clear enough that I was confident it was the right one. Three days and six screws later the machine was working fine.

Removed lid (top of washer), then ran a cycle in normal to identify the failed component, then noticed the water inlet valve assembly for the hot water was leaking, used my pc and went to website Part Select and found to failed part on the parts break down item, then ordered the part, the part "Valve Assembly Inlet" for the hot water arrived 2-days later, replaced valve in less than 5-minutes, disconnected push on electrical connector, unscrewed the valve assembly inlet and installed the new valve assembly inlet, very easy

Simply took hose off from inside machine and replaced it with new one. The tore one had a stopper on one end that wrapped to front machine; inside filter compartment. So I put stopper on the other end of new hose and wrapped it to it's holding spot in filter compartment.

found the leak, went to the website, called customer service, ordered the part... $24 later, problem solved. Great customer service and on-line support

pulled off top of washer to get at the inlet valve disconnect two hoses take two screws out and then you put it back together the way you took apart and your done

First we unplugged the machine. Then turned off the water and disconnected the hoses. Pulled out the machine and laid it on its side to access the themsistor located on the drum. (No, you do not have to remove the control panel at all to replace this part) The thermsistor is clearly seen with a flashlight. There were plastic ties holding the wires of the thermsistor so we used small scissors to cut the ties. Then unplugged the old thermsistor and plugged in the new thermsistor and used a regular bag twist to secure the wires. Repair complete and the machine is back to normal. Thank you Part Select.

It was so easy. i searched my model it brought up this site and the most common problem popped up without my even asking and recommended the part. i got it one week later and it was so simple to fix. a repair man wanted three times the part price to come to my home twice and would have had to wait longer. you guys were very helpful

new pump was a little different ,but mounted properly. Tipped washer on its side, changed pump by working trough bottom and back access. It went pretty smoothly, works fine.

Unplug Washing machine first. Then remove 2 screws at the back of the top cover. Slide the top cover back then lift and remove. Unplug electrical connector @ inlet valve and remove water lines 1 going in and 1 out of valve. Remove 2 screws holding assembly in place then install new valve assembly and all other components in reverse order.

Found great Youtube video, followed step by step. Only difficult part was getting the tub gasket clamp back on. But all in all pretty easy. If tub won't drain and weird noise coming from pump do not hesitate to do it yourself and save some coin!

After checking for blockage on the drain hose and checking on any blockage on the bottom left corner filter and not finding anything i decided to open the machine. Everything suggested a broken drain pump
ITEM
PS3579318 Drain Pump and Motor Assembly which is located on the bottom left corner also and it attaches to the bottom left corner filter. And voila! The machine did not work! Now started throwing a FE code and it would not fill up. Well, the new pump was stuck! All i had to do was to stick my fingers in the bottom left corner filter orifice and move the fan like devices that make the new drain pump work, that did it! Be careful not to do it while the machine is pluged in, those plastic blades may hurt your fingers. To reach the drain pump you have to take the top, control board and front (door and gasket) of the machine off, about one hour labor.