WD90210BD (ABWEEUS) LG Washer - Parts

The drain pump and motor assembly may also be known as the washer drain pump and is a part for your washer. The drain pump helps expel water from the washing machine. The drain pump is activated after the spin cycle speed is maintained for a specific period of time. To make this installation you will need a Phillips screwdriver, a small f...Read morelat-blade screwdriver, a pair of needle-nose pliers, and a pair of slip-joint pliers. Note that the pump casing is not included. This medium-difficulty repair may vary, but can generally be started by disconnecting power, then removing the top of the washer by taking out the four back screws and two small brackets. Then, remove the front panel by taking out the two screws and eight tabs that should be taken from the top. Moving down the front of the washer, remove the door, latch, tub gasket, and drain cover. Disconnect the drain hoses and clip from under the drain assembly, and install new assembly from there. Reassemble parts in direct reverse order -- taking photos during disassembly and keeping parts clearly organized can help here. Despite the number of steps, you will only need a standard Phillips screwdriver to complete this repair.

This hot water inlet valve is designed to regulate water flow into the washing machine during operation. Featuring a standard hose fitting inlet and a single water outlet, it opens as needed to allow hot water into the appliance. If the valve is defective, you may notice slow filling, no filling at all, or water leaks. A simple way to tes...Read moret the valve is to unplug the washer when the issue occurs—if water continues to flow, the valve is likely faulty and should be replaced. The part measures approximately 3 inches in length by 3 inches in width and is sold individually.

This washer sensor assembly, also known as a motor rotor position sensor, is a genuine OEM replacement part designed to monitor the direction and speed of the rotor during operation. By communicating this data to the electronic control board, it ensures proper spin and agitation cycles. A malfunctioning sensor may result in the washer pum...Read moreping but failing to spin or agitate, leading to incomplete wash cycles. This part is sold individually and is compatible with select washer models. For safety, always disconnect power before beginning installation, and verify model compatibility prior to purchase.

This door lock assembly is a critical component in compatible washing machines, responsible for confirming that the door is securely closed before initiating a wash cycle. When functioning properly, it communicates with the control system to engage the locking mechanism. A faulty switch may prevent the door from latching, opening, or star...Read moreting the cycle. Located behind the front panel, replacement requires removal of the door gasket and access to the internal housing. Sold individually.

This hose has bellows to allow for flexibility during the wash and spin cycles.

This round rubber tub seal is designed to prevent water leakage between the front and rear halves of the outer tub in select washing machines. Positioned at the junction of the tub components, it compresses during operation to maintain a watertight seal, ensuring efficient washing performance and protecting internal components from moistu...Read morere damage. A worn or damaged seal may result in water leaks, unusual operational noises, or reduced washing effectiveness. Replacing the seal restores proper containment and supports the overall functionality and longevity of the appliance. Installation may require partial disassembly of the tub assembly.

This part is called a spider, spinner support or rear drum support for your washer. It is triangular, with three arms, and it is made of metal. The washer spinner supports and spins the tub while the washer is running. If you notice that your washer shakes or moves during operation, or if it is excessively noisy, you may need to replace t...Read morehe spider. This part is sold individually and is an authentic OEM part sourced directly from the manufacturer.

This replacement pump filter, also known as a filter assembly, is a genuine OEM part for your washer or washer/dryer combo. Before beginning this repair, turn off the power and water supply to your washer. The filter assembly may need to be replaced because it is broken or is leaking water. To locate the filter assembly, pry open the smal...Read morel door on the front of the washer, using a flat-blade screwdriver. Unplug the drain hose next to the filter and drain the water into a bucket. Then unscrew the pump filter, and replace with your new one.

This part is the replacement connector hose or clean-out drain hose for your washer. It is black in color and is sold individually. The connector hose drains water out of the washer if the drain cycle is not working. If the hose breaks, it will not be able to drain the water properly, and you may experience a water leak. Be sure to discon...Read morenect your washer from the power source, as well as the water source before you begin this repair. This is an OEM part sourced directly from the manufacturer.