WD12439BDA (ACREEUS) LG Washer - Instructions

Remove where the water pumps are and remove the one that was damaged easily

Unscrewed 2 screws holding part. Removed old part & replaced with new.

It went great. First of all, thank you Part Select for the video on how to do this myself. My home warranty company was giving me a hard time. Blah, blah, blah. A mechanic friend of mine referred me to this site. Within minutes I found the part I need and a GREAT!!!! price. Ordered it, got it super fast, fixed it my self and my second hand washer is no longer peeing all over the floor. Very very happy. I will definitely be a repeat customer, hopefully not anytime soon.
Thank you again for an amazing experience.

Unplugged washer.
Disconnected water line,
Removed 2 screws then removed clips for hoses on inlet valve.
Replaced valve and hooked hises back up. Replaced plate or rear of washer and plugged back in.
Works great and even with cost of 1 day delivery, saved at least $200 doing myself.

This was a very easy repair. Just followed the steps in the videos on the website (I replaced both the hot and cold inlet valves, so two different videos, but the process for each is similar) and it couldn't have been simpler.

WATCHED VIDEO PROVIDED BY PART SELECT, AND FOLLOWED INSTRUCTIONS. VERY SIMPLE REPAIR.

Used Youtube to look for a set of repair instructions. From start to end 35 min.

The difficult part was getting the door back on. Only 1 Youtube video I watched stated Do not remove the 2 center screws at the top. Wish I had seen that video first.

Overall very easy to do.

I followed the video. Everything worked exactly as described. i ran a quick cycle and everything seemed to be fine. Started a wash and the machine was going fine but stopped, and wouldn't drain. I thought that maybe it might be the Rotor Position Sensor assembly, which I had already purchased just in case.But first i drained the machine and checked out the pump filter. Plugged solid. I'm guessing when the pump went there must have been a lot of lint and debris in the machine. something you might want to check out, after that repair. Thanks. you guys saved me a couple of hundred dollars

After watching the video for installation of the bellow, I followed the suggested repair method and was able to repair my washer.

First I had to elevate the washer on 3-5 gal. buckets in order to get underneath it and find the leak. Then I tried to repair the hose itself-which actually worked-but then the rest of the hose just started splitting everywhere I touched it. So I ordered the new part which took some careful comparing and examination online. But it was exactly the right part. You have to remove the top of the washer which is just 2 or 3 screws. Then taking the hose out was a little challenge-knowing I would have to put the new one back in carefully. Use Vaseline on rubber fitting at the end of the hose that connects to the washer. Need at least 2 people to raise the washer up in air to work on it.

I went by the video

1 tilt washer back
2 remove cover plate screw from front of drain filter access panel.
3 Remove cover plate and remove 2 more mounting screws .
4 go below washer and pull down sliding clip and move pump assembly back.
5 remove wires and 3 mounting screws around pump housing
6 Swap pump and re-attch wires

ridiculously easy. removed the door gasket ring clamp. separated the gasket from the face. unscrewed the lock, removed the wire(gently). replaced the wire on the new lock. replaced the lock. replaced door gasket and ring clamp. washed clothes. Note- I had called a repair service and was given a $360 estimate in addition to the $130 dollar service charge. All total- $50 dollar part(with shipping), less than 45 min total time and I'm no mechanic!

Followed instructions on YouTube link. Replaced the shock absorber and washer is working really well.

just put new part in very simple only problem was shipping yall used fedex went to 4 states and one state twice they finally gave it to USPS so it took almost 9 days to get here