WD10212BD (ABWEEUS) LG Washer - Instructions

Followed the manufacturers instructions to disassemble the washer from the top. There was a video on youtube of a guy who was able to replace his bellows hose from the back, but maybe my arms weren't long enough, I couldn't reach all the way to the front. The washer was pretty easy to take apart, except for taking off the top, where there were 2 extra screws not mentioned in the instructions. Replacing the part was really easy. HERE'S THE MOST IMPORTANT PART: LG DOESN'T MENTION IT IS REALLY HARD TO GET THE CLAMP ASSEMBLY BACK ON THE GASKET WITHOUT A SPECIAL TOOL. You can buy the special LG tool, or you can do what I did (and others on the internet) and buy an $8 "Brake spring spreader" tool at your local auto parts store. Repair was a success. No more water leaking!

greate very easy and the parts fit awsome the shiping was fast and easy very satified

Took apart the washer and removed bearings and shaft on spider. My advice would be to order the spider and shaft (one piece) hen ordering the bearings, seal, and tub gasket. If the bearings are gone, it is likely the shaft is gone too as mine was.

complet disassembly , took almost everything out of the interior . removed the drum holding the agitator and disassembled it . then removed the seal and bearing and replaced with new. also removed seal between drums and replaced it . put it all back and run more quite than when it was new. PS- no leeks!

Removed the top, the front, got to the pump, removed it and replace it with the new one.

Found the part of Part Select by describing the problem. used a Utube video and step by step we were able to take apart, replace and put back everything with just a screw driver - I saved so much money!

The pump is apparently used for more than one washer, and the R&R instructions may be significantly different. I found a youtube video for my exact washer.

My washer would try to spin and remove the water according to the time allowed. Consequently my washer would take longer than the time allowed to drain therefore water would send a code error then the machine would stop working. So I remove the hose from the pump and found my son's little small sock blocking the drain. I removed the sock and reinstalled all hoses. Everything is fine now. No need for a replacement item. Just a little servicing.

Found on line OE meant washer not pumping out water with the suggestion to clean the filter and inspect the pump and lines for blockage. No problems there. You must be careful to empty the water manually before removing the filter. My wet vac helped but I still made a mess. I found a mechanic to look at the washer. He said it is common for the pump on these washers to go bad, especially if the washer has sat out of service. They wanted $300 to replace the pump. I found the part on this website for $53 and replaced it myself. The only hard part was emptying the water without making a mess and leaning the washer up and back far enough safely to remove the pump, then working on my back under the machine.

Found great Youtube video, followed step by step. Only difficult part was getting the tub gasket clamp back on. But all in all pretty easy. If tub won't drain and weird noise coming from pump do not hesitate to do it yourself and save some coin!

Disconnected power. Removed washer top, upper front control panel, and front panel. Removed hoses from washer drum housing. Removed cabling and support springs and stabilizers. Removed drum housing from cabinet. Removed bolts that secure the two halves of housing. Removed rotor from drum shaft. Removed stator from housing. Supported drum housing and with hammer and punch, removed drum shaft from bearings. Replaced bearings and seal and reassembled in reverse order.

Tipped the washer on its side to expose the bottom, removed the plastic lid adjacent to the pump after removing the screws holding it , then, using a flat head on a pry tab pulled out the pump, removed the hoses with pliers to complete the extraction, swapped the pump on my bench. . assembly is reverse of disassembly. .

Another friend of mine did the repair.I watched him remove the old Drain pump and Motor Assembly and the Circulation Pump Motor.He installed the new parts in 45 to 60 minutes. The washer works like a new one. I had never ordered from Parts Select before. I was amazed how fast I received the new parts. Order placed on line on Friday , received the order at my home on Saturday afternoon.I will tell my friends about Parts Select and I will buy from them in the future.