WD-90282BD LG Washer - Parts

The drain pump and motor assembly may also be known as the washer drain pump and is a part for your washer. The drain pump helps expel water from the washing machine. The drain pump is activated after the spin cycle speed is maintained for a specific period of time. To make this installation you will need a Phillips screwdriver, a small f...Read morelat-blade screwdriver, a pair of needle-nose pliers, and a pair of slip-joint pliers. Note that the pump casing is not included. This medium-difficulty repair may vary, but can generally be started by disconnecting power, then removing the top of the washer by taking out the four back screws and two small brackets. Then, remove the front panel by taking out the two screws and eight tabs that should be taken from the top. Moving down the front of the washer, remove the door, latch, tub gasket, and drain cover. Disconnect the drain hoses and clip from under the drain assembly, and install new assembly from there. Reassemble parts in direct reverse order -- taking photos during disassembly and keeping parts clearly organized can help here. Despite the number of steps, you will only need a standard Phillips screwdriver to complete this repair.

This hot water inlet valve is designed to regulate water flow into the washing machine during operation. Featuring a standard hose fitting inlet and a single water outlet, it opens as needed to allow hot water into the appliance. If the valve is defective, you may notice slow filling, no filling at all, or water leaks. A simple way to tes...Read moret the valve is to unplug the washer when the issue occurs—if water continues to flow, the valve is likely faulty and should be replaced. The part measures approximately 3 inches in length by 3 inches in width and is sold individually.

This washer hose with bellows, also known as a dispenser hose, is a genuine OEM replacement part for your washer. Replacing this part can be helpful if your washer is leaking. The dispenser hose connects the dispenser assembly to the tub. Before beginning the repair, unplug the washer and turn off the water supply. You will need a Phillip...Read mores head screwdriver to complete this repair; a clamp tool can also be helpful. Remove the screws holding the lid of the washer in place, and take off the lid. Locate the dispenser hose and remove its clamps. Place the clamps on the new hose, using the arrows for a guide in positioning the clamps. Install the new hose and reassemble all other parts.

This door lock assembly is a critical component in compatible washing machines, responsible for confirming that the door is securely closed before initiating a wash cycle. When functioning properly, it communicates with the control system to engage the locking mechanism. A faulty switch may prevent the door from latching, opening, or star...Read moreting the cycle. Located behind the front panel, replacement requires removal of the door gasket and access to the internal housing. Sold individually.

If your washer isn’t filling properly or skipping parts of the cycle, this water valve might be the issue. It controls cold water flow for the bleach dispenser and prewash cycles. The valve connects with a standard hose and has three outlets—two pointing to the right and one to the left—all at a 45-degree angle. It’s a genuine part and ea...Read moresy to install, but be sure to unplug your washer and turn off the water before starting.

Sold individually.

This replacement pump filter, also known as a filter assembly, is a genuine OEM part for your washer or washer/dryer combo. Before beginning this repair, turn off the power and water supply to your washer. The filter assembly may need to be replaced because it is broken or is leaking water. To locate the filter assembly, pry open the smal...Read morel door on the front of the washer, using a flat-blade screwdriver. Unplug the drain hose next to the filter and drain the water into a bucket. Then unscrew the pump filter, and replace with your new one.

This genuine OEM drum seal gasket prevents water from leaking between the outer tub and spin basket of your washer. It is made of black rubber and measures 2.5 inches in diameter. If your washer is leaking, and running noisier than usual, check for wear on the gasket, and to ensure it is properly fitted.

This part is the replacement connector hose or clean-out drain hose for your washer. It is black in color and is sold individually. The connector hose drains water out of the washer if the drain cycle is not working. If the hose breaks, it will not be able to drain the water properly, and you may experience a water leak. Be sure to discon...Read morenect your washer from the power source, as well as the water source before you begin this repair. This is an OEM part sourced directly from the manufacturer.

This Noise Filter Assembly reduces electromagnetic noise and shields the control board from power surges, ensuring smooth and reliable operation. It helps minimize vibration and noise during cycles for a quieter experience. For safety, disconnect power before installation.

This ball bearing reduces friction and supports smooth rotation of moving components. Proper bearing function minimizes noise and wear. Replacing a worn bearing restores quiet, efficient operation.