WD-1274FHB LG Washer - Instructions

Removed lid (top of washer), then ran a cycle in normal to identify the failed component, then noticed the water inlet valve assembly for the hot water was leaking, used my pc and went to website Part Select and found to failed part on the parts break down item, then ordered the part, the part "Valve Assembly Inlet" for the hot water arrived 2-days later, replaced valve in less than 5-minutes, disconnected push on electrical connector, unscrewed the valve assembly inlet and installed the new valve assembly inlet, very easy

First we unplugged the machine. Then turned off the water and disconnected the hoses. Pulled out the machine and laid it on its side to access the themsistor located on the drum. (No, you do not have to remove the control panel at all to replace this part) The thermsistor is clearly seen with a flashlight. There were plastic ties holding the wires of the thermsistor so we used small scissors to cut the ties. Then unplugged the old thermsistor and plugged in the new thermsistor and used a regular bag twist to secure the wires. Repair complete and the machine is back to normal. Thank you Part Select.

Turn off hot water supply and activate a cycle on the washer momentarily, with hot water selected on front panel options to relieve hose pressure. Slide washer out to gain access to rear of unit. Unplug washer from AC source. Using pliers, remove washer supply hose from washer-side of the line (water may drain from hose) Remove single Phillips screw at bottom of each nylon lid holder at rear. Using a plastic putty knife, place between front panel and top lid to loosen lid and slide to rear. Remove lid and store aside. Hot and cold inlet valves sit side-by-side at top rear of the unit. Disconnect connector from valve by pulling gently away from valve plug prongs and place to the side. Using pliers, compress hose clamp and move to lower section of hose. Carefully rotate hose back and forth to remove from assembly. Inlet valve is held to washer body rear with 3 small Phillips screws. Remove first 2 and then while holding inlet valve body, remove final screw to free inlet valve assembly. Replace with new assembly by reversing these steps.Make certain when supply hose is reconnected, it is firmly tightened but DO NOT over tighten. Test washer by running a cycle to ensure there are no leaks.

I watched a video of how to replace the pump and it showed taking the top and front off to get to it. I actually found this could be done by removing the back panel from the washer. There were two hose clamps you have to squeeze and slide up and two wires going to the pump. There are three screws holding the pump that need to be removed from the front of the washer. Once these are removed all you have to do is push a tab down and the motor slide right out. The pump assembly can also be reached from the bottom of the washer.

new pump was a little different ,but mounted properly. Tipped washer on its side, changed pump by working trough bottom and back access. It went pretty smoothly, works fine.

The machine was making a grinding noise instead of draining. I spoke with the LG rep on the 800 line and was told to call a repair man. The Parts select diagram helped me to identify the part I needed. It was clear enough that I was confident it was the right one. Three days and six screws later the machine was working fine.

This was very easy to instal. The aplaiance repair co. wanted $240 my LG is six years old and would rather buy a new one if I had to spend that much, so I gave it a shot and it took me 20 min to install the part. Told my wife she owed me $ 180 for my labor.

took out the drain pump and replace with a new one

During my troubleshooting, I removed the bottom to access the drain pump. I had to cut some wire ties so that I could make removing the wires easier. After checking the pump and putting everything back together, I determined that the pump itself was bad. Pump impeller should not rotate freely! After receiving new part, I installed it relatively easy. I didn't have to remove the bottom since there was enough room through the access hole. Just make sure to make where wires go before removing old part.

It was so easy. i searched my model it brought up this site and the most common problem popped up without my even asking and recommended the part. i got it one week later and it was so simple to fix. a repair man wanted three times the part price to come to my home twice and would have had to wait longer. you guys were very helpful