WD-12416BD LG Washer - Instructions

The repair went well and your parts are easy to find. This is the second time I have used your services and both times have been great. Your parts are at great prices and your delivery is a lot faster that one would think.
Thank you

The bellows hose on the bottom of the tube had worn through where it flexed. This was an easy job except for the long reach you had to make under the washer to reach the hose clamps that held the part in place. These were spring loaded clamps which were easy to remove with pliers. I replaced them with ones that could be tightened with a socket wrench since it was hard to replace the sprung clamps.

UNPLUG WASHER.Unscrew 4 screws holding silver plate at back of unit. Remove plate to expose inside of unit. Locate drain hose at bottom of washer tub. Hose connects at front drain, bottom of tub, and at rear at the pressure sensor. Front and rear simply slide clamps down by grasping clamp tabs and sliding clamp off connection point. Disconnect from tub bottom by loosening main clamp with Phillips screwdriver and pulling downward. Have a towel handy as there will be water in the hose, and it will pour out when removing it from the unit. Installation is the reverse of removal. ATTACH THE HOSE ASSEMBLY TO THE DRUM FIRST, THEN FRONT, THEN LASTLY REAR. This order is the easiest way, otherwise you will spend extra minutes trying to get the tub connection to seat properly. Plug it back in (duh), then you're good to go for another 4 years or so until another hole wears in the hose. I have performed this repair on 3 different units, with 4 years being the average lifespan of this part.

pulled off top of washer to get at the inlet valve disconnect two hoses take two screws out and then you put it back together the way you took apart and your done

Turn off hot water supply and activate a cycle on the washer momentarily, with hot water selected on front panel options to relieve hose pressure. Slide washer out to gain access to rear of unit. Unplug washer from AC source. Using pliers, remove washer supply hose from washer-side of the line (water may drain from hose) Remove single Phillips screw at bottom of each nylon lid holder at rear. Using a plastic putty knife, place between front panel and top lid to loosen lid and slide to rear. Remove lid and store aside. Hot and cold inlet valves sit side-by-side at top rear of the unit. Disconnect connector from valve by pulling gently away from valve plug prongs and place to the side. Using pliers, compress hose clamp and move to lower section of hose. Carefully rotate hose back and forth to remove from assembly. Inlet valve is held to washer body rear with 3 small Phillips screws. Remove first 2 and then while holding inlet valve body, remove final screw to free inlet valve assembly. Replace with new assembly by reversing these steps.Make certain when supply hose is reconnected, it is firmly tightened but DO NOT over tighten. Test washer by running a cycle to ensure there are no leaks.

Unplug Washing machine first. Then remove 2 screws at the back of the top cover. Slide the top cover back then lift and remove. Unplug electrical connector @ inlet valve and remove water lines 1 going in and 1 out of valve. Remove 2 screws holding assembly in place then install new valve assembly and all other components in reverse order.

1. Remove Power from washing machine. Using an ajustable wrench,remove both the cold water and hot water hoses/lines from back of washing machine. 2. Unscrew the back plate, using the screwdriver (Phillips) and store back plate and screws for re-installation. 3. Using a small screwdriver (Phillips), remove the retaining plate fom the cold and hot water inlet valves and store plate and screws for re-installation. 4. Using the pliers, press the retaining clamp and slide it through the hose; remove the hot water valve assembly; drain water from the hose (be careful: hot water can scald and burn). Mark the electrical connection and the hot water hose. 5. Using the pliers again, press the retaining clamps and slide them through the hoses/lines;remove the cold water valve assembly and the cold water hoses/lines; drain water from hoses/lines. Mark the electrical connections and the cold water hoses/lines. 6. Remove new inlet valves from boxes and re-install in accordance with marking on hoses/lines and electrical connections. Using the pliers, move clamps over all the hoses/lines to tighten ends on inlet valves. 7. Replace retaining brackets on cold and hot water inlet valves and re-insert screws. 8. Replace the back plate and screws. 9. Power the washing machine by reconnecting the power cord into the electrical outlet. 10. Test the repairs by placing the washing machine in the "Rinse and Spin" cycle and check for leaks. If no leaks are detected, repair is complete.

Removed the old bellows (2 squeeze hose clamps and one screw adjustable hose clamp) slid on the new one and it was done!

Did the repair entirely from the back.- 4 screws back cover comes off. Once you see the Bellows it is obvious what needs to come off and there are other videos on the net showing this. The main things I did differently were 1) Leaned the washer forward and placed 3 2x4 blocks of wood under each back leg. This allowed me to reach under the washer with one hand, and through the back with the other. You need both hands in there ! 2) Uninstalling is easy with just pliers. But on the way back in, I used a pair of Locking Pliers to keep the circular clamp squeezed as much as possible. That seemed the only way to get the bellows back in. Another option would be to switch to screw on Pipe clamps instead of the spring clamps.

Took off the old one and put the other one on. The only difficulty was that my husband has big hands and had a hard time getting to one end.

Removed lid (top of washer), then ran a cycle in normal to identify the failed component, then noticed the water inlet valve assembly for the hot water was leaking, used my pc and went to website Part Select and found to failed part on the parts break down item, then ordered the part, the part "Valve Assembly Inlet" for the hot water arrived 2-days later, replaced valve in less than 5-minutes, disconnected push on electrical connector, unscrewed the valve assembly inlet and installed the new valve assembly inlet, very easy

Replaced rotor assembly by removing the back panel off the washer. Removed center bolt to be able to take out roto assembly. Magnets made it a little resistant, but with a little wiggling came off fairly easily.

Contacted LG customer service, not much help there. Watched a very helpful Utube video on how to find and repair the leak. The video suggested that the most common leak is in the drain hose with bellows. Removed the rear panel and removed the bellows unit using pliers for the clamps and screwdriver for the bellows part. This was pretty easy. The rubber bellows was leaking in the exact same place as the youtube video showed. This is a Design Flaw that LG needs to fix. Ordered the new part and installed the bellows portion of the part first, as the angle for that installation needs to be correct. Then attempted to install the end of the hose (very inaccesible) to the pump drain. Very difficult to position the factory supplied spring clamp with pliers so I purchased a screw-type clamp (using the nut-driver rather than a screw-driver to tighten the clamp was helpful) at the local hardware store and that made my job much easier. Note: My unit is mounted on a pedestal, so it was a little easier to access the part location (about one foot off the floor, rather than at floor level), but it may be that the part should be replaced from the bottom of the unit, which would make it much easier to access. Then I installed the other end of the hose to the drain line using a screw-type clamp. I am 69 years old, and not that flexible anymore, so getting down on the floor to reach inside the unit was difficult. You need patience to do this job and you have to make sure all the clamps are properly installed so you don't start the machine up and end up with another leak. For me, this process was difficult and took more than two hours to complete. Limited access to the area made it more difficult and I hate the factory clamps they use. Overall, the repair costs about $25, compared to the $125 just to come look at the machine, then more money to fix the unit. It was satisfying to complete the repair for a small amount of money, but not sure it was worth the aggravation.

Followed the manufacturers instructions to disassemble the washer from the top. There was a video on youtube of a guy who was able to replace his bellows hose from the back, but maybe my arms weren't long enough, I couldn't reach all the way to the front. The washer was pretty easy to take apart, except for taking off the top, where there were 2 extra screws not mentioned in the instructions. Replacing the part was really easy. HERE'S THE MOST IMPORTANT PART: LG DOESN'T MENTION IT IS REALLY HARD TO GET THE CLAMP ASSEMBLY BACK ON THE GASKET WITHOUT A SPECIAL TOOL. You can buy the special LG tool, or you can do what I did (and others on the internet) and buy an $8 "Brake spring spreader" tool at your local auto parts store. Repair was a success. No more water leaking!

Took apart the washer and removed bearings and shaft on spider. My advice would be to order the spider and shaft (one piece) hen ordering the bearings, seal, and tub gasket. If the bearings are gone, it is likely the shaft is gone too as mine was.