WCSR2090G6WW General Electric Washer - Instructions

This repair was a no brainer repair. The factory replacement knob that I bought from this site comes with a new "D"-Ring. Some other aftermarket parts houses sell the knob and the "D"-Ring as seperate parts. The knob from this site already has the "D"-Ring ring installed in the knob. My "D"-ring was broken and I simply removed it with ... Read more my fingers. All I had to do was properly align the new know knob with the timer shaft and press it into place. If your "D"-ring is not broken and not still inside the old knob, you will need to pull it off the shaft with a pair of pliers before pressing the new knob onto the timer shaft. Dr. "B" The Hot Rod Doc

Removed the front panel. Removed the washer top. Removed and replaced each strap. Very simple repair.

I pushed a small screwdriver under the top lid and pulled the front out and lifted it out or the way. The rubber hose had two clamps holding it. One you loosen with a flat screwdriver and the other one you squeeze with pliers to remove hose.Then replace hose and put front back on. It's very simple.

Watched the video. Followed the instructions. This has to be one of the best sites I have ever encountered. Even a caveman could fix the problem after watching the video.

Could have removed debis in old pump. Kept it as a spare.
Replacement was simple , (two nuts) & (2 Lg. Hose Clamps) + two wires.
Dealer wanted $168.00 Labor + $67.00 for part!.

I reviewed the service guide on Partselect and was able to take the old knob off the washer and say that the teeth on the knob had worn off, I called in and ordered the part on Saturday and the part was delivered in Wednesday, within 2 minuets from getting home from work the washer was fixed. My wife was ready to go out and buy a new wash ... Read more er when it only cost a little over $13.00 to get it fixed.

Surprisingly easy. I took the screws off, then pulled off the drain hose. I then inserted the new hose, and put back the screws. Amazing quick!

Removed clip from knob and pulled out old knob.Then got new knob and installed with the new clip ,very easy job.

pulled front panel off it snaps in but had to get off. then remove two bolts holding too down. moved top around to get to straps. front to easy 5/16 deep socket aND rather .the other end has 1/4 socket back hard to get too not bad. took 30 minutes. didn't fix problem. on bottom of motor looks like it had rubber bumpers but none there didn ... Read more 't find any on parts list. went to parts house auto got two rubber freeze plugs installed them in hole on bottom of motor that stopped the noise and rube moves very little now. also install new belt . install it put it on motor then on part of pulley then roll pull while keeping belt on motor roll pulley around till belt on all the way then roll pull more pushing on belt on motor till belt fit in all groves then roll it couple more times it will line groves up on pull. install top back down then snap front panel it your done.

I followed instructional video on partselect.com, it was very easy, but it didn't take care of the problem. I got to to order "TRIPLE WATER VALVE" and that did the trick. After opening the washer first time (for water fill nozzle), it took me even less time. You don't have to take the front panel off to replace the water valve.

Followed the video guidance supplied by this site

Pull hose out from wall and drain water into bucket. Remove two screws from back of washer holding on the clip. Pull hose out from washer its in there about 3 inches or so . If you order a new clip will make this even easier it's only $3.87 and I didn't realize I needed it. So, I just cut the old hose with a small saw near the clip so I c ... Read more ould remove it and reuse it. Just slide the clip onto the end of the new hose - it fits into one of the grooves-I just made a note of where that was before removing from old hose. Then replace the two screws on the clip going to the back of washer. Put other end of hose into pipe in wall.

Could not complete repair. The pulsator was rusted on the shaft, used wd 40, finally pried off the shaft. The hub nut was so corroded on the shaft I could not remove it. Reassembled the Machine.

I had to insert a broom stick to keep the drive pulley from rotating as I hammered the tub nut loose.

2nd tip, my washer has the standard agitator with the glued on cap; it was unclear if I needed to remove it; you should clarify that this is not necessary, that one must only pop up the entire agitator; I used a shipping strap ... Read more looped under the agitator and over a 2x4 across the top of the frame, tightening until the tub was raised a bit and then a gentle pop down on the tub and the agitator easily popped off.

This was a easy job for the do it your selfer. I had no problem the part ,it was like the same one I took off. Now I know where to come for parts . It was perfect . Thanks again