TUD6000JQ0 Estate Dishwasher - Instructions

I followed the video available on partselect.com and was easily able to follow step by step the process of removing and reinstalling a new Drain and Wash Impeller and Check Ball.

Had to be careful positioning the spring without breaking the hinge pin. Requires a certain amount of patience.

Turned off electricity. Removed the interior door cover. Removed door switch. Replaced switches & reversed process. By the way - I am a woman & diagnosised, ordered part & fixed it myself - I have no experience in this field. THANKS for all your information on your site.

The bracket that holds the rack up had broken. I ordered a new part and snapped it in place. Not much to explain.

but the pin in and add the pin though the 2 tabs close door on it open it up move the springs backwards to the door

I used a pair of needle nose pliers to remove the
Upper Wash Arm Support Clip from the broken support arm. Very quick re-assemble with the new part and I was able to re-use the support clip. The upper wash sprayer unit with its new support arm easily clipped in place on the upper rack.

remove star screws holding inside door panel. remove plastic cover that protects latch assembly. hook one end of spring on stationary pin on inside of slider bar. Hook other end of spring on pin on slider bar. replace cover and door panel.

looked up on line from partselect.com, ordered the part and when it arrived, removed the broken wheel and inserted new one, took 5 minutes

Just put it on by hand, works great now, saved me at least 50.00!

removed two hose clamps and old hose. slid new hose on existing fittings on dishwasher drain and disposal and tightened hose clamps. Turned it on for test run.

I used the screwdriver to pry the old lid off of the horizontal pin upon which it rotates. One must be careful before removing the old lid to note how the return spring is deployed. The short legs on the spring must be in the lip of the lid before you snap the new lid onto the horizontal pin. It was helpful to lubricate the two catches on the lid that snap on the pin with some liquid soap before attempting to snap them on the pin. After the lid is snapped into place and the short legs of the coil spring are in the lip of the lid, use needle nose pliers to attach the other end of the coil spring to the pillar where it was before you removed the old lid. There are videos showing how to do this on Youtube. The spring part is a little tricky. The video makes it look a bit easier than it is..

Replaced door gasget took 5 minutes tops. Ran cycle and still had leak. Called local repair person. After thoroughly checking out the dishwasher and running soapless cycle determined problem to be soap build up over time. He ran a commercial cleaner through a complete pots and pan cycle. No more suds and no more leak repair complete. Did not actually need door gagset but it was super easy to change and delivery service was great.

Actually I ordered the drain and wash impeller kit because it was listed as the #1 cause of failure to drain. I then hired a plumber to install it. He did so and that didn't solve the problem. So I was about to buy a new dishwasher. I then noticed that the second most frequent cause was a problem with the "dishwasher drain check valve." I watched the "partselect" video on how to change that. I didn't have a new one but I thought I would take out the part and see what I could learn. As it turned out it was blocked by a little piece of what appeared to be a walnut chip. I cleaned it out reinstalled the drain check valve and the problem was solved.

Installed pump kit. Was surprised the kit seemed different( some parts changed or deleted. Instructed to discard old parts and follow with new configuration. Reassembled and tried t fin it works fine now. Thank you so much

Once the covers under the door are removed, the check valve is visible (unless its too dark, hence the headlight), and pointing right at you. Since I was working under the dishwasher, I gathered all the tools I thought I might need and laid them on the floor next to. Removed 2 covers, placed pan under check valve and hose to catch any water, squeezed clamp with (wrong) pliers, it eventually came loose. Carefully twisted hose off check valve. Water came out, some of it got into the pan, most of it on the floor. I guess I should have pumped it out before I started this. Plastic check valve is screwed into the big piece of whatever, carefully grabbed it with (wrong again) pliers and turned it out. Installation is reverse of removal - but use a large pliers with a ROUNDED jaw to grab the round check valve body. Don't squeeze too hard or overtighten it. Put the clamp on the valve before pushing the hose on. Be sure the hose seats all the way onto the little lugs. Compress the clamp, slide it over the end of the hose and release. That's all folks, works good now.