TGP310KW0 Estate Range - Instructions

I removed the handle by unscrewing two philips screws located on the each side on the top inside of the door. I then placed the glass bottom end in first, lined it up on both ends, put the handle back in place and put the screws back.

I removed the two screws that held the igntr in place. Then I pulled the igntr out and unplugged the wires. Replaced the igntr with the two screws and plugged the wires back together. I then turned the oven on to 400 degrees and it heated like a new one.

Un-screwed 4 screws. Got part numbers off of the pieces. Put numbers in blank on web site and ordered the pieces. Parts cam in 4 days later and installed the pieces with my trusty screwdriver.

Remove 2 screws holding oven bottom in place.Lift out the plate and replace with new plate. The hardest part of the replacement was lining up the screw holes. By the way i have never received such great service from any internet company as Part Select. I ordered the part on a Monday and the part was at my home the NEXT DAY and installed that evening.

After I found the web site I looked at the possible solutions for my problem. My igniter was glowing so I was not sure that would fix the problem but several places indicated the igniter would fix the problem and after I replaced it the oven work great.

Unsrewed what was left of the trim and oven handle. Just 4 screws total, then replaced the 2 screws of the trim and the 2 screws on handle.
Finished! Replacement parts fit perfect!!! Thanks a milliion!

I didn't. Don't know how to get to light bulb to change it for this specific model

I didn't do it, but I suggest putting down newspaper to keep from having to clean up all the charred remains that will inevitably fall from the parts you have to remove. First, unplug the thing so you don't shock yourself. I removed all the racks for easy access to the drip pan, which had to be removed by unscrewing two screws. Then there was a cover over the flame area that also required two screws being removed. The coil had two screws connecting it, but first I had to pull out the drawer at the bottom, crawl under the unit and unplug the coil. I removed the two screws from the old coil and replaced it with the new one, but first I had to get back under and plug in the new coil. I was unprepared for the virtual small animals that were under the stove, so I took some time to clean out that mess. I tested the thing to make sure it would work, and it did. I put all the pieces back in reverse order and had some really good baked chicken for dinner. I also recommend using gloves, as all the soot is hell on your nice manicure.

Removed two screws holding the bottom in, pulled out old bottom, inserted new bottom, replaced screws and tightened them. Total time less than five minutes.

simple change out - remove old grates, install new ones - note that this site/store is excellent

1993 model oven, built in wall model, so didn't to remove oven for the normal rear access to replace the lamp socket. As someone else posted, replacement can be done from inside the oven -- BUT the socket removal was more complex than just 'twisting it out.' But below worked! (1) Turned off oven power at circuit breaker panel. To facilitate working in the oven compartment, removed oven door (2 screws on back of door), raised the over door almost closed, put 2 large nails through the hinge holes when they lined up. Lifted the door out (heavy ~20-25 lbs) and put aside. (2) Put work light inside oven. (3) unscrew glass socket lens and the bulb). (3) Using inspection mirror, studied the inside of the socket to determine that its lock tab type and locations -> were on left and right sides of the socket. These tabs needed to be bent in, but they were each held out by a small circumferential length of think metal, a tab about 3/16" x 3/8". These small tabs could be moved/positioned by just finger friction, with a little start with a screwdriver tip on their edge! I got an end positioned to put sharp screwdriver under that end, then pried it (bent it) inward a short distance. Enough to use needle-nosed pliers to pull it completely out - came fairly easily. Repeated on other side of socket. (4) Then, with pliers, bent each of the 4 locking tabs inward a short distance, Used sharp tool to get one socket edge lifted a small amount; then use mini-pry bar and screwdriver to gently pry around the socket in steps, working evenly around its edge. At about 3/8", it was free. Lifted it inward gently so as not to damage the insulation of the 2 wires attached to its rear. Noted the direction of the wire tabs was straight up (keep same orientation on new socket). (5) Needle-nosed pliers on each connector to gently work the connectors off their socket tabs. Note one tab is larger than the other. Keep the wires inside the oven compartment. Don't damage the insulation. (6) Pushed the wire connectors onto their respective new socket tabs. Aligned socket with the tabs upward, and inserted it, careful to nurse the wires back into the oven wall hole; press socket into the hole, pushing it in evenly and firmly until flush. (7) Pushed in the new type bulb that came with new Socket. Turned on power, and light came on. (8) screwed on new glass cover. (9) Lifted oven back onto the hinge prongs. (easier with two people to get the prongs aligned and into their door slots.) Worked door left and right to get it to lower down fully. Removed nails, lowered door, and put its 2 screws back on. (10) Poured a glass of wine.

Our existing gas stove burner igniter had broken on one of the four burners. I therefore obtained a replacement igniter and mounting screw form PartSelect.com which were indeed perfect replacement parts. However, I could not remove the burner plates from the top of the stove since they were basically welded into position by years of heat. I therefore followed instructions as submitted by a previous customer (thank you Michael of Bloomington, Il), snapped open the stove lid retainer clips, and then lifted the stove surface about 4 inches. Through that opening I was able to reach the underside of the involved burner. Unfortunately, I could not unscrew the existing broken igniter mounting screw and therefore had to break off the already broken igniter and grind down the remaining mounting screw using a drill grinder since the screw was basically welded into place. Once I did that, I was then able to install the new igniter using a separate unused screw hole already in place right beside the old previous mounting screw. With that done, the new igniter works perfectly and the burner works just like new. It was however a lengthy process over two hours long because of the glitches described above. Nevertheless I'm very pleased that the parts were perfect and the repair is complete.

Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.

Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.

the research and diagnosis took much longer than the repair on this model. if i had the new igniter on hand, it would have been only about 15 mins.

Remove the side covers. Remove the 2 screws on the back side of the door, hold on to the glass and front panel, they will fall out. remove the 2 screws holding the handle. Put the new handle in place and insert screws, note the old handle had metal inserts that are threaded, the new does not. Had to push very hard and let the screws bite into the plastic.