TEF326FBC Tappan Range - Parts

The Oven Bake Element is a black, metal part which supplies heat to the oven. This element is 19-1/2" wide x 18-1/2" long and has 3-1/2" inserts. It is rated as "Easy" to install by users, and attaches to the bottom of the oven. If you notice visible damage, or that your oven is not receiving heat properly then it may be a problem with th...Read moreis part. Check your model number and user manual to see if this is the right part for you. It is important for you to disconnect your appliance from the power source before performing this repair. After disconnecting your appliance, remove the two screws/nuts connecting the old element, pull it out, and discard if faulty. Simply connect the new element prongs where the old element fit, and screw it back in. You may need a flashlight when making this repair.

This surface burner terminal block kit comes with interchangeable mounting brackets, terminal box, ceramic wire nuts, heat shrink protective tubing and wires.

This surface burner switch controls the stove top 8-inch surface burner temperature. This switch is 240-volt, 2100-2600 watt, and 8.8-10.8 amp. If your element is not defective but will not heat, you may need to replace the switch. This burner switch is a genuine OEM part. It is recommended to disconnect the power to your range before you start your repair.

This rear drawer glide is for your bottom range drawer. It is sold individually.

This is the electronic clock timer mechanism only. The overlay or touch pad is NOT included. To get the overlay, please use the model# of your appliance to search.

This is an 8-inch drip bowl for your range or cooktop. It is made of porcelain and is black in color. Place the drip pan under your burner to catch food that may drip or spill while you cook. It is 10 inches in total diameter. Be sure to wait until drip pan and burner are cool to the touch before completing this replacement.

This 40-watt appliance light bulb is a reliable replacement for use in select ranges, refrigerators, freezers, and microwaves. It provides bright, consistent lighting to help you see clearly inside your appliance. Installation is simple—just unscrew the old bulb and replace it with the new one. If the existing bulb is broken, disconnect p...Read moreower and use needle-nose pliers to safely remove the remaining base. Sold individually, this bulb is a commonly replaced part—consider keeping a spare on hand.

This front drawer glide is for your bottom range drawer. Your range has 4 in total. This drawer glide is sold individually.

This drip bowl is a genuine OEM replacement part for your stovetop. It is black in color, made of porcelain, and six inches in diameter. To replace the drip pan, you simply need to remove the burner element. It may be held in place by a spring-loaded mechanism. Pop out the burner, remove the old drip pan and clean up any cooking residue, and replace with the new drip pan.

The coil burner element is eight inches in diameter. It has four turns, 220 volts and looped terminal ends. The coil burner element provides heat to the cooking surface on your range. You might need to replace this part if your element is not heating. It might have shorted out around the coil or the terminal block; you can test the coil t...Read moreo see if the burner or the switch may be at fault. Please make sure the power has been disconnected and the element is turned off and had time to cool before starting your repair. The element is a genuine OEM part and is sold individually.

This switch controls the stove top surface burner.

Sold individually. This part is sold individually. This is a part for your stove top. The surface element is what your cookware sits on. The element supplies heat at varying temperatures. This may need to be replaced if the coil has shorted out or the terminal block shorted, and this caused the connectors at the end to burn out. The eleme...Read morent is set in place by springs. You will need to push the springs in to release the old element. Make sure the drip bowl is lined up with the terminal block and press the new element into place.