Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
One screw that held the roller would not hold as the hole in the case was stripped. I knew when I removed original as there was material in the screw threads
3 of 3 peoplefound this instruction helpful.
Richard from MOUNT AIRY, MD
Difficult
More than 2 hours
I used both epoxy on the male threads and then pulled out the case and twisted the flat car body flat kind of a nut. Let it sit for 36 hours and now like new.
Removed old hose and went to install new hose from Part Select. Part received was not the same as advertised. It was 6-8 inches shorter than the original hose. Would not make the necessary turns because of shorter length. I even went to Video instruction on installation even though I have been in Machine repair for 30 years , this video s
... Read morehowed using the shorter hose and when installed in the video hose also had a kink because of hose length. Had to stop repair and go to hardware store and purchase a longer hose. This purchased hose from the hardware was 50% cheaper and actually worked. I also paid for 2-3 day shipping and received part 7 days later. I am very disappointed with Parts Select and am an owner of an Equipment Rental Facility and will never utilize Parts Select again.
Read less
Was this helpful?
Thank you for voting!
Spray arm had come off and melted on the heat coil
3 of 3 peoplefound this instruction helpful.
Bonnie from SPOKANE VLY, WA
Really Easy
Less than 15 mins
New piece snapped right on
Was this helpful?
Thank you for voting!
dispenser cover wouldn't stay closed
3 of 3 peoplefound this instruction helpful.
Jeff from TREVOSE, PA
Really Easy
15 - 30 mins
Screw drivers
Removed two screws,one on each side of the bottom part of the door. The door cover then comes off. Then 6 screws hold on the dispenser. Shut off power and remove two wire connections. Replace dispenser. Replace lower door cover and two screws. Done.
Was this helpful?
Thank you for voting!
Door Spring broke
3 of 3 peoplefound this instruction helpful.
Robert from BAY SHORE, NY
Very Easy
15 - 30 mins
Pliers, Screw drivers
Removed the two screws that mount to count top pulled the dishwasher out to see how the spring was attached , installed the new spring and the job was done the job it took about 15 mins. to complete.
Was this helpful?
Thank you for voting!
Missing tub gasket
3 of 3 peoplefound this instruction helpful.
John from FALLBROOK, CA
Very Easy
15 - 30 mins
Pliers, Screw drivers
I think the videos on the site are awesome. Made both repairs after watching them. They explain the repairs in a simple to follow way.
First of all, I got the part 24 hours after I ordered it. That in it self was a feat. Second, I followed everyone elses instructions, pulled the old gasket out with a pair of needle nose pliers, cleaned the area as good as I could, found the notch for the slot on the gasket to slide into and viola...it slid in and stayed in. No more leaka
... Read morege whatsoever! Thanks for all of the tips!
Read less
Was this helpful?
Thank you for voting!
Bottom Basket Cage Broken Rack &, Spray Arm Falls Off
3 of 3 peoplefound this instruction helpful.
MICHAEL from PHILADELPHIA, PA
Very Easy
Less than 15 mins
1. Engage B.R.A.I.N. : B: Break open the Box. You know you'll never get it back in R: Read Instructions: It's not more packing material. A: Assemble New One: Put it together just like the old one I: Ignore Instruction: Seriously, sharp edges will cut me? N Never listen to the w
... Read moreife Or at least pretend to be listening
Dishwasher door strike piece broke. Door had to be propped closed each time dishwasher was used.
4 of 6 peoplefound this instruction helpful.
Charles from Fort Washington, MD
Really Easy
Less than 15 mins
Nutdriver
Took out the two retaining screws and pulled the unit forward. Took the old door strike out and put in the new one. This site is where I go for all my appliance repair parts!!!
Was this helpful?
Thank you for voting!
Leaking Dishwasher
3 of 3 peoplefound this instruction helpful.
Andre from La Mirada, CA
Really Easy
Less than 15 mins
The old gasket was worn. I pulled out the old one, put in the new gasket. I trimmed the ends to fit and that was it.
Was this helpful?
Thank you for voting!
Dish washer leaking at the door
4 of 6 peoplefound this instruction helpful.
Brian from Milford, MA
Really Easy
Less than 15 mins
Pulled off the old gasket and replaced it the same way with the new one.
Was this helpful?
Thank you for voting!
Water leaking from bottom door seal.
3 of 4 peoplefound this instruction helpful.
Don from Jackson, TN
Really Easy
Less than 15 mins
Simply pulled old gasket out with hand, and slid the new one in place!
Was this helpful?
Thank you for voting!
leaking bottom door gasket
3 of 4 peoplefound this instruction helpful.
Wayne from Prfovincetown, MA
Really Easy
Less than 15 mins
Pliers
Used pliers to pull out the old gasket. New gasket snapped into place. Notice where notches in the gasket are when the old one is removed, so the new one can be properly oriented. It was not necessary to remove the door.
Was this helpful?
Thank you for voting!
Dishwasher was leaking at the front, just below the door
3 of 4 peoplefound this instruction helpful.
Jim from Woodburn, OR
Really Easy
Less than 15 mins
I measured the length of the gasket, using the old one to measure the length. Cut it to that length and installed it. VERY SIMPLE TO DO! But it didn't stop my leak--turns out there was a small leak in the bottom of the tub that was easily fixed with some silicone. The dishwasher's like new now!
Was this helpful?
Thank you for voting!
Leaking underneath dishwasher
3 of 4 peoplefound this instruction helpful.
Lora from Shelter Island Heights, NY
Really Easy
Less than 15 mins
My dishwasher started leaking at the beginning of the summer. We didn't know what to do, but didn't want to call an appliance repairman. Towards fall, a friend came over and pulled it out and found the heating element brass nut which was broken. We put it back in and washed dishes the old-fashioned way for another 3 months after that. I a
... Read moresked at my local hardware store for the part, and thought about trying one of those big-box do-it-yourself stores but never got around to it. Finally after getting sick and tired of doing all the dishes in the house by hand, I found your site, and the part I needed and ordered two (just-in-case). A few days later, we got the part, I pulled the dishwasher out again, screwed on the new nut by hand and put it back into place. We're in business!
My Orders
