TDB210RFS1 Tappan Dishwasher - Instructions

After figuring out the problem wasn't the water inlet switch, I replaced the switch assembly for the water level float. Cut off supply water to dishwasher, removed the 2 screws holding switch assembly, and installed new switch. 15 minutes, very easy job.

Pulled out old gasket from bottom of door with needle nosed pliers and then put in new one in.

Removed the bottom panel on the unit (2 screws hold it on) and pulled the dishwasher out about 4"--after turning off electricity to the unit. Removed the broken spring and the old linkage and replaced them with the new parts. Pushed the diswasher back into place, and replaced the bottom panel. Turned on the electricity and the diswashe ... Read more r door is "good as new." This is quite simple to do; just takes patience.

I removed the dishwasher from the cabinet space (two screws) and manually replaced both springs. I replaced one spring first to see if there would be an improvement when the second new spring was installed. There was much better tension once the second new spring was added.That is why changing both springs is recommended. This was very ea ... Read more sy.
Changing the gasket was scary because I thought the the whole door would have to be taken apart. You know nothing ever goes back together the same. I feared that I would create an even bigger leak than what I had. Taken the door apart didnt work for me, so I just pulled the old gasket by hand and pressed in the new one. I made sure that it was seated correctly. Voila no leak.
The dishwasher is running as good as new.
I ordered these parts on Friday morning. They were on my door step Monday morning,
I highly recommend ordering from this site.

Unscrewed dishwasher from cabinet and pulled out about 1 foot. Took bottom plate off of dishwasher. Undid clamp on hose of discharge of inlet water valve and removed hose. Shut off water to water inlet valve and removed. Took wiring clip off of water inlet valve. Removed 2 screws holding water inlet valve in place. Installed new wat ... Read more er inlet valve in reverse order.

Make sure power is off. Remove metal toe kick with fillips screw driver. Reach under dishwasher with 1/2" open
end wrench and completly unscrew brass nuts from element ends. Then open door and pull element ends straight up. Note: As you pull element ends up (inside washer) you are also forcing the element end wire connectors to come ... Read more off underneath. The electricial connectors are very hard to get off any other way.

Wendell Hensley
Madiso0nville, Tn

Fully open dishwasher door to horizontal position, remove lower dishwasher rack and relocate to another temp location, grab old lower door seal from right or left corner and pull completely out of door, lay the old bottom seal aside facing the same direction as once installed (seal has a notched side which faces the right side of door), m ... Read more atch direction of the new seal with the old seal (match the notched side of seal to the right side of door), gently push the seal into the door starting on the right side (notched side of seal fits tightly into a receiving area inside the door), and finally push the remaining portion of the seal into door (aligning with the right side already properly seated inside dishwasher door). Close dishwasher and run water cycle to confirm leak.

Only took me 5 sec, just push it in. Good as new. Thanks for the fast deliver .

I had to remove the dishwasher from under the counter. I then had to unscrew (from the bottom) the bolts that held the heater in place. After that I ran into a problem of disconnecting the wires that ran to the heater. I did not want to "force" the wires off and I was unsure how exactly to remove them. I figured out that they are real ... Read more ly hard to pull off but there are no clips holding them on, so you won't break anything off. Once I got the wires off, I was able to screw the nuts onto the new heater and put it back into place.

Pulled the dishwasher out and laid it on its back. From under the dishwasher I unscrewed three screws and freed the drain pump from some sort of frame. Then with the pliers loosed the orange clamp that held the black hose to it. Then unscrewed the clamp that held the white hose to it. Then pulled out the purple and white fuse wires. T ... Read more hese wires were very tight I used pliers to get them off. The pump was free. Be sure to have a bowl to catch all the water. There wasn't a lot but it stinks. Then put it all together the way I took it apart. The dishwasher works perfectly now.

The Parts finder was the big help. After that all that was needed was to loosen the clamps and replace the old hose with the new one A piece of cake. Slide the washer back into place and replace the screws that hold it to the counter. Out and back in, 30min. top end to complet the job

I had to remove the dishwasher from under the counter, flip it on it's side to gain access to the discharge hose attachment point, removeit, remove the other end of the hose from the sink-side and replace the hose. The sink-end of the hose has a 'collar' that must be cut to fit the fitting on the sink.

Pulled the broken one off, snapped the new one on.

Water had been dripping for quite some time causing the floor boards to warp and buckle causing the door to no longer align. Water drip could be seen coming from the motor area. Ordered the O rings and replaced. Get Motor & Pump schematic Pub to visualize how parts fit together. I recommend getting motor (~$90)which comes with O rings ( ... Read more ~$50 for O rings alone) because, as it turns out, the leak was in motor. I will post repair process in separate posting.

Much easier than I expected. The bottom of the door gasket simply pulled out and the new one slid back into the same spot without any issues. That gasket did not solve the problem. The unit continued to leak. We waited for the back ordered door gasket approximately 2 week to come in. Once it came in the process took about 10 minutes. ... Read more The old gasket easily pulled out of it's groove around the door. That gasket was dried out and worn in several places. We fitted the new gasket in the groove, trimmed off the excess, closed the door and ran the dishwasher and had no leaks. The two gaskets definitely did the trick. This is an easy DIY for anyone and the parts were priced right!!