TC607X3 Jenn-Air Trash Compactor - Instructions

Pull unit from under counter (Held in place with 2 screws) Use nut driver to remove top and front panel. (I didn't remove the control panel from the front panel which probably made access more difficult) Locate the directional switch near the top of the unit and remove two screws, being careful not to lose a small metal plate into which ... Read more the screws thread (similar to a Tinneman nut). I moved the wires one at a time from the old switch to the new as I am color blind and have trouble with wire colors. Fit the new switch in place, being sure the switch lever is positioned against the metal tab that operates it. Screw the switch in place and then reassemble the compactor.

Laid appliance on side - removed top sheet metal cover and bottom sheet metal cover. Broken delrin ring gear was on bottom of bottom cover (housing). Gear had broken off of its hub, which also was the sprocket chain drive for both acme screws driving the compactor platten. Motor had to be loosened so that the chain could be removed f ... Read more rom the old sprocket hub, and the new delrin ring gear - with new sprocket hub attached - could be mounted on its fixed spindle. With new delrin gear/chain sprocket mounted, the motor had to be spaced and tightened to allow 0.010 inch lash between the gears. The only instructions included with the new gear was how to do this - by placing a piece of paper in between the pinion gear on the motor, and the new ring gear, and then tightening the motor into place. This was done, the sheet metal covers were re-installed, and the compactor works just fine. There is a design flaw in the original (KitchenAid) engineering of the gear, however, and I expect that in the next four years this will probably happen again.

Ordered new door hinge and used available You Tube Video. to assist in installation. Not a very difficult job, however that did not solve the problem. Then in an attempt to complicate the solution, I again removed the door and took the entire inside cover off. The entire latch mechanism fell on the floor. It took a very long time to det ... Read more ermine how the latch mechanism was placed. Finally with the help of a neighbor the latch was placed back into position, the glass and screen replaced and finally all the plastic molding seated and screwed tight. Guess what the latch now seated correctly and appears to work correctly.

Kitchenaid had a problem with its footswitch. It was a flimsy piece of metal that pushed in a switch. The flimsy metal part is no longer produced, and they have a replacement kit. The instructions provided that you pull the frame apart, but I was able to do it by coaxing out the old switch, reconnecting and inserting the new switch, and ... Read more then drilling and screwing in the new switch actuator. The old switch activated the unit when pushed in, the new switch activates the unit when let out.

Took out old gears replaced with new very easy with your dirictions.

replaced the large gear and put it back together.

Thanks to Parts Select and their detailed instructions it turn out great! Replacement Parts fit Great!

All I really needed to do was to take the front facing off and put on the new container, but I took the opportunity to do a complete overhaul and cleaning. It now work like a new compactor.

Followed PartsSelect instructions, the Compactor was appoximately $1000. when I purchased it. The kit was $26.14. I will forever be a customer of this company. Thank you, Brian

Took the bent one out, put the new one in. The repair was not the story, the story was that we ordered the part on Monday afternoon and it was delivered on Tuesday! And the shipping was less than $8.00. Fresno to Elk Creek in less than 24 hours for that price was amazing!

Replaced drive gears.They arrived in a kit from Parts Select with instructions.They fit perfectly and the compactor works like new.

easy ... got the new bag holder and replaced old one. the impressive part of the process is how easy it was to get the part info from partselect website. could have spun my wheels a lot without that.

took longer to pull it out and put it backunder the counter then to pull the panel take the chane gear & drive gear off and put it back together

I took the hex screws out with a nut driver and then punched out the role pin in the pinion gear (the little gear) and replaced it along with the large gear, less than 15 minutes. I was surprised how fast (day and a half) the parts were here.

take 2 screws out on top cover with key switch. remove two screw holding directional switch. remove wires, one at a time, and place on the new switch. put new switch in place with two screws. put front cover on with two screws and test. works like a charm.