TC400 - Instructions

Removed unit from under counter. Moved to garage. removed Top, Bottom plates, and switch controller. Turned upside down and removed power screw nuts One came off easy. One side frozen. Took large pliers and worked nut off of drive screw. Removed ram. Ordered two new power screw nuts. Lubed screws, chain, nuts, rollers and cleaned ... Read more whole unit. Straightened ram which was bent from so many years of use. Unit 26 years old. Replaced all plates and plugged it in. Works like a champ. Thanks for carrying parts for a unit this old.

Trash compactor was stuck, took apart to see the power nut stripped, ordered nuts and while putting the ram back in I didnt see the reversing switch lever and broke it off.Guess Ill order a new switch ($40)..moral of story...slow down and pay attention to the details..

Replaced both, results like new.

Laid compactor over on its side. REMOVED 5 SCREWS holding cover plate to expose gear drive. Found that large drive broke in half. Used screwdriver to start split ring then pliers to pull it off the rest of the way.Take off the washer . Next I needed to losten the 4 nuts holding the drive motor. This allowed me to slip the rest of the driv ... Read more e gear off the drive shaft. It was then a simple matter to put the new gear back on the chain then slide the whole thing back on the drive shaft. Replace the washer then slip the split ring back in place and seat it home with the pliers. Retighten 4 nuts on motor support. Put cover back on with 5 screws 2 in front 3 in back Pushed button it worked.I must mention that this was a Sears compactor but when I went to their online parts they no longer supported it. I found Part select and they suggested I look at a Kitchenaid compactor and after checking out the picture it looked the same,Iordered the part and it was the same. Thanks I guess I'll come to you first now.

replaced rotatory switch (10mins) problem solved

removed old parts and replaced

Emptied all garbage! Laid machine on its side. Removed cover. Removed left over gear parts by removing pin. Loosened chain by removing two top left corner screws. Place new plastic gear in position with chain. Returned screws to top left corners. Returned pin to gears. Make sure chain is taught. Replace cover. Lift back up from i ... Read more ts side. Test.

There were no instructions that came with the parts kit other than how to set the spacing for the gear lash. There were parts in the kit which I have no idea what they are (4 inch long plastic pipes?. Having 4 years experience with Sunbeam appliance repair was an asset. The old melted and broken gear came off easily with a few strikes of ... Read more a hammer on a flat blade screwdriver. The replacement gear was a perfect match and the scroll pin was put in with a little gusto effort (tight fit as it should be). It would be great if just one gear or the other could be ordered....

Removed bottom and replaced gears

After inspecting to make sure the actuator was functional and that power to the unit was not an issue I was able to find that one the drive gears cracked in half and made the compactor inoperable. It was easy to remove the bottom casing with a nut driver. This casing covered the drive gear which operated the ram. After slightly loosening ... Read more the gear mounts and I was able to replace center gear and re-attach gear chain and re-tighten. Then replace bottom casing and the compactor was back in action. Huge savings!

Removed the gear cover at the bottom of the compactor. Loosened the slack on the chain. Replaced the gear drive. Replaced the gear cover. Worked like new. No major obstacles.

replaced power nuts

the bearing were the perfect match and instructions helpful. sysem is rolling smoothly

Same problem as described previously on this site. Pulled unit out and replaced the gear as described. Thanks for the info - would have been tough with out it.

Pull unit from under counter (Held in place with 2 screws) Use nut driver to remove top and front panel. (I didn't remove the control panel from the front panel which probably made access more difficult) Locate the directional switch near the top of the unit and remove two screws, being careful not to lose a small metal plate into which ... Read more the screws thread (similar to a Tinneman nut). I moved the wires one at a time from the old switch to the new as I am color blind and have trouble with wire colors. Fit the new switch in place, being sure the switch lever is positioned against the metal tab that operates it. Screw the switch in place and then reassemble the compactor.