It is important to remove the dishwasher to a workable space. Probably best to set it on a slightly higher platform, otherwise you're on the floor.
1. remove racks, 2. disconnect power supply and water line (turn off at source). 3. remove the exterior insulation. 4. One can now access the harness from both side o
... Read moref the washer. 5. Inspect and determine what connection goes where, all have color coded wire.Connections are notched 6. Recommend that each connection is removed and new connection replaced at that time 7.removing screws from the inside door to connect the harness to select connection. 7.button-up the door, replace insulation and reattach water line and power, reinstall machine. 8. You may have to remove the front toe-kick to access routing the wires.
Read less
Was this helpful?
Thank you for voting!
Handle caps at both ends of dishwasher door cracked and needed to be replaced
5 of 5 peoplefound this instruction helpful.
Robert from VERONA, NJ
Really Easy
30 - 60 mins
Followed You Tube video how to replace door handle caps and used above mentioned tool. Note: could not use a regular screwdriver.
Was this helpful?
Thank you for voting!
Water leak on top of door.
6 of 8 peoplefound this instruction helpful.
Phyllis from CLERMONT, FL
Very Easy
Less than 15 mins
Went to on line video and followed it. The old gasket came right out and the new one fit right in. Started at the top middle and worked the gasket in on both sides to make sure it was evenly spaced.
Was this helpful?
Thank you for voting!
Filter-Micro was clogged with lime from hard water.
5 of 6 peoplefound this instruction helpful.
Peter from LEXINGTON, KY
Very Easy
Less than 15 mins
Replacement was fast and very simple. Was completed in less than 5 minutes.
Was this helpful?
Thank you for voting!
dishwasher door would not close properly, spray arm would not engage plug
5 of 6 peoplefound this instruction helpful.
Brian from MADISON, CT
Really Easy
Less than 15 mins
popped off old spray arm from under the rack and put on new spray arm, couldn't be any easier, 5 minute job, door closes easily now!
Was this helpful?
Thank you for voting!
The washer had an error message in the display of E:09. I called Bosh on customer srevice and she said that the heat pump was not working and needed to be replaced. Since the motor is the main part for this that needed to be replaced as well. The pars were under $200.00 total so we oted to fix this
6 of 9 peoplefound this instruction helpful.
Claire from ALPINE, AZ
Very Easy
15 - 30 mins
Screw drivers, Wrench (Adjustable)
We followed the video and had no problems with leaks at all afterwards. The parts fit perfectly and the machine is working great again.
Water leaking and high pitch noise mid way through operation.
5 of 7 peoplefound this instruction helpful.
Lowell from SALEM, OR
Easy
1- 2 hours
Nutdriver, Pliers, Screw drivers
Mistakenly opened covers for the drain pump. Had to put those covers back in place. Heater and pump installed easily with a bit of careful maneuvering the plugs and plug housing from the exterior. Pump installed in place easily. Clamp fit perfectly.
Removed the dishwasher from the cabinet, laid it on its side, removed the old pump/heater, installed the new and reinstalled the dishwasher. What made this a little more difficult is my dishwasher has a bottom to it that would be very difficult to remove, access to the pump is from the side! I have large hands, not much room to work!
Was this helpful?
Thank you for voting!
Inlet valve was leaking water at all times causing the unit to shut down with the bottom tray collecting water.
4 of 5 peoplefound this instruction helpful.
Ronald from WASHINGTON, MI
Easy
1- 2 hours
Pliers, Screw drivers, Wrench (Adjustable)
Repair was simple once the problem was diagnosed with the inlet valve. Most of the work was in disconnecting the necessary lines so the dishwasher could be removed from the cabinets to replace the bad valve. Replacing the valve was easy. Reinstalling the dishwasher was just the reverse of the removal. The replacement part matched
... Read more the original and solved the problem we had.
Read less
Was this helpful?
Thank you for voting!
The old basket didn’t fit in the new lower rack
4 of 5 peoplefound this instruction helpful.
Pat from Wichita, KS
Very Easy
30 - 60 mins
just placed the basket in the rack
Was this helpful?
Thank you for voting!
Wheels on the bottom tray broke off
4 of 5 peoplefound this instruction helpful.
Phyllis from BAYTOWN, TX
Really Easy
Less than 15 mins
The repair was extremely simple. Just lined up and popped them on. No tools needed.
Was this helpful?
Thank you for voting!
There was a roller missing from the lower washing rack.
6 of 11 peoplefound this instruction helpful.
George from STURGEON BAY, WI
Really Easy
Less than 15 mins
There were 5 rollers still in place so I used them to show me how to snap the replacement roller in place.
Was this helpful?
Thank you for voting!
Over the years the filter became too clogged with embedded particles
4 of 5 peoplefound this instruction helpful.
Jim from EDINA, MN
Really Easy
Less than 15 mins
Really simple. You pull out the drain filter plate and pull the filter off the support and replace. I gave everything a good cleaning and put it back in place.
Was this helpful?
Thank you for voting!
The lower dish rack was rusting.
3 of 3 peoplefound this instruction helpful.
Sara from LA CROSSE, WI
Very Easy
Less than 15 mins
Replaced lower dish rack
Was this helpful?
Thank you for voting!
Four wheels on the lower dishwasher rack came off and got lost.
3 of 4 peoplefound this instruction helpful.
james from PARSIPPANY, NJ
Really Easy
Less than 15 mins
I bought replacement wheels. I put them on the post, and they snapped onto the vertical post very easily. Job done.
My Orders
