Home
SHVM98W73N
Instructions

SHVM98W73N (01) Bosch Dishwasher - Instructions

All Instructions for the SHVM98W73N

Spray arm plug into water source became worn out and difficult to engage

2 of 2 people found this instruction helpful.

David from Sequim, WA
Really Easy
Less than 15 mins

The spray arm makes a slide in attachment to a slide out drawer. It was removed by forcing out of the connection on the back of the drawer and the replacement was installed by sliding it into the same connection point.

Was this helpful?

Water leakage from the dishwasher; unknown source.

2 of 2 people found this instruction helpful.

Bill from Seattle, WA
Really Easy
Less than 15 mins

Followed the video on your site and it was an easy install with no more leakage.

Was this helpful?

Torn rubber flap that blocks the noise under the dishwasher from getting out into the room

2 of 2 people found this instruction helpful.

Ellen from Edina, MN
Very Easy
Less than 15 mins
Screw drivers

This repair was extremely simple. Unscrew the toe kick, peel off the adhesive strip on the old flap, stick on the new flap, replace the toe kick
Some online parts reviews from other providers mention the part arriving rolled up and difficult to flatten. The one I purchased from this site arrived in a flat box, ready to install.

Was this helpful?

Chronic water leakage

2 of 3 people found this instruction helpful.

Callan from CHICAGO, IL
Difficult
More than 2 hours
Pliers, Screw drivers, Socket set

Replaced ‘sump’ housing , seal was leaking on it- replaced inop float on water level warning system switch, and switch itself as well- replaced drain pump motor attached to sump- replaced o-ring seal at water sprayer inlet valve- replaced water inlet plastic assemble on side of dishwasher- replaced drain hose out of sump assembly.
... Read more r />Used YouTube video to understand repair- this is an involved repair in time and complexity- dishwasher eventually gets turned upside down once removed and stripped down, to remove the white plastic water pan , which then allows access to the guts of all the above parts- some critical seals only come with new assemblies, so you are buying that new part to get a new seal and ensure no new leaks from what you took apart.
Read less

Was this helpful?

Thank you for voting!

New Sray arm and wheel replacement

4 of 9 people found this instruction helpful.

Charles from SANTA ROSA, CA

Really Easy

Less than 15 mins

They just snap in

Other Parts Used:

Dishwasher Spray Arm

SPRAY ARM

Dishrack Roller - Grey

Was this helpful?

Thank you for voting!

One Dishwasher bottom rack wheel broke

2 of 3 people found this instruction helpful.

Toni from GREENSBORO, NC

Very Easy

Less than 15 mins

Popped the new one right on!

Was this helpful?

Thank you for voting!

The top door gasket on dishwasher cabinet was torn

1 person found this instruction helpful.

Thomas from BAY VILLAGE, OH

Very Easy

Less than 15 mins

Part arrived on time. Double checked it was the part I needed. I unclipped the old seal and snapped the new piece in place.

Was this helpful?

Thank you for voting!

Top arm water connection to rear wall - all seals eroded and leaking

1 of 2 people found this instruction helpful.

James from MOORPARK, CA

Really Easy

Less than 15 mins

Removed the middle basket and turned it upside down. Unplugged the spray arm from the middle basket. Snapped the new spray arm into the middle basket.
Installed middle basket into slides.
It works great. Great site for parts - reasonable prices too

Was this helpful?

Thank you for voting!

A rat got under the dishwasher and chewed up the electric’s and the hoses

2 of 5 people found this instruction helpful.

Nathan from LOS ANGELES, CA

A Bit Difficult

More than 2 hours

Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)

A rat got under the dishwasher and chewed up the electric’s and the hoses. Only found out when the air light came on drain not working Lots of water underneath as well as all kinds or shoot insulation and rat droppings had to wear a mask affect him use a bunch of Clorox before I could diagnose it a real party And hard to reach corners. ... Read more r /> I ordered four parts since I found a better deal on the main electric cable which a rat head chewed through until it had an electrocuted itself. These four parts came in three different boxes and three different deliveries over two weeks. not efficient. But handwashing is over put it all together and it works I soaked the hose in hot water so I could fit it on.
Read less

Other Parts Used:

ROPE

HOSE

FLOAT

Was this helpful?

Thank you for voting!

Pressure washer would not maintain pressure

1 of 5 people found this instruction helpful.

Scott from MOUNT JULIET, TN

Really Easy

30 - 60 mins

Pliers, Screw drivers, Wrench (Adjustable)

Determined that the unloader valve was leaking.
Removed the unloader valve from valve body.
I could see a crack in the nylon portion of the valve. This would not let the relief valve operate.
Went to the internet (Part Select) and found the replacement valve. There are a lot of different sizes of unloader valve. Partselect ... Read more help me select the correct valve.
The key was the valve body, the unloader valve inserts into the valve body. There are two types of valve bodies, a 4 bolt and a 5 bolt. They look the same but do not interchange. I needed the 4 bolt.
I was nervous as the new unloader valve was a different construction than my old valve. It worked perfectly.
Replacement was easy.
Locate the unloader valve. It is part of the pump body. You can recognize it by the spring extending out from the valve body.
Remove the “U” shaped clip that holds the unloader valve in the valve body.
I used pliers to grab the spring and pulled the unloader valve from the valve body. It took a little pulling pressure to remove.
Note the orientation of the unloader valve I. The valve body. You want to install the unloader valve with the same orientation.
It may take a little force to seat the valve. I used a little silicone grease to lube the valve. A small tap on the end of the valve to insure it is fully seated.
It has to be seated so the “U” shaped retaining clip can be inserted to hold the unloader valve in place. Again, a light tap was necessary to fully seat the clip.
That was it, I was back operating my pressure washer
Read less

Was this helpful?

Thank you for voting!

All Instructions for the SHVM98W73N

31 - 40 of 40
Prev
1
2
3
Next