SHV68TL3UC/09 Bosch Dishwasher - Instructions

Went to on line video and followed it. The old gasket came right out and the new one fit right in. Started at the top middle and worked the gasket in on both sides to make sure it was evenly spaced.

We followed the video and had no problems with leaks at all afterwards. The parts fit perfectly and the machine is working great again.

Replacement was fast and very simple. Was completed in less than 5 minutes.

Slip the wheel onto the axle, snap the clip facing up onto the frame

popped off old spray arm from under the rack and put on new spray arm,
couldn't be any easier, 5 minute job, door closes easily now!

Mistakenly opened covers for the drain pump. Had to put those covers back in place.
Heater and pump installed easily with a bit of careful maneuvering the plugs and plug housing from the exterior. Pump installed in place easily. Clamp fit perfectly.

Removed the dishwasher from the cabinet, laid it on its side, removed the old pump/heater, installed the new and reinstalled the dishwasher. What made this a little more difficult is my dishwasher has a bottom to it that would be very difficult to remove, access to the pump is from the side! I have large hands, not much room to work!

just placed the basket in the rack

Repair was simple once the problem was diagnosed with the inlet valve.
Most of the work was in disconnecting the necessary lines so the dishwasher could be removed from the cabinets to replace the bad valve. Replacing the valve was easy. Reinstalling the dishwasher was just the reverse of the removal. The replacement part matched ... Read more the original and solved the problem we had.

Really simple. You pull out the drain filter plate and pull the filter off the support and replace. I gave everything a good cleaning and put it back in place.

Replaced lower dish rack

Easily removed the old one by carefully pulling it and repeated this procedure to replace it. Total time took less than 15 minutes

To remove the old cutlery drawer I had to pull the old drawer forward and work the rollers over the stops at the end of the permanently installed slides. To install the new cutlery drawer, I reversed the procedure and worked the rollers on the new drawer over the slide stops and seat the new basket. No tools were required.

A ... Read more s for the crockery baskets, the larger lower basket was very simple. Roll it forward onto the door and lift it out. To install the new basket reverse the procedure. Place the new basket on the door and slide it in on its rollers.

For the upper crockery basket the procedure is more complex. The retaining mechanisms for the upper basket appear to be very complet as they have a number of moving parts intricately engineered. With a little study, it become apparent releasing the locks and levers which keep the basket from rolling out and falling to the floor are well designed to both secure the basket and to remove. Each anchoring mechanism has a lever at the base and by depressing the lever it releases the basket so it can be rolled forward over the stops at the end of the slides. Some manual dexterity is required to maintain pressure on the mechanisms to ensure the basket will be released. The procedure is quickly mastered with a few attempts. The good thing is again no tools are required.

My new tray and baskets are working fine and it is a relief to have the old rusting and deteriorating tray and basket replaced. This is true for both safeguarding the crockery and cutlery form rust and chemical of deteriorating plastics, rusting metal, and bonding agents. More important, I am sure replacing the old deteriorating baskets and tray guards against any potential health issues.

The problem and solution were described on the internet. I ordered a set of 4 wheels for $43+. I received one wheel. When I called Drew told me that the order was correct, but the description on the web page was wrong. He was to sent me a return label, but it has not arrived. Since then I went to the Bosch website, found the set of wheels ... Read more (Part 10016657) for $42. They have been installed and the problem seems to have been fixed.

The spray arm makes a slide in attachment to a slide out drawer. It was removed by forcing out of the connection on the back of the drawer and the replacement was installed by sliding it into the same connection point.