All Installation Instructions for Bosch Dishwasher SHU33A02

Water leak on top of door.

Went to on line video and followed it. The old gasket came right out and the new one fit right in. Started at the top middle and worked the gasket in on both sides to make sure it was evenly spaced.

Parts Used:

Door Seal

Phyllis from CLERMONT, FL
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

6 of 6 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Dish washer would fill and leak when not in use

Turn off power to unit!
-Remove kick panel,2 screws.
-remove water valve, 2 screws, 3 electrical connections, 1 hose clamp.
-Remove elbow from old valve and install on the new valve ( use teflon pipe tape)
-replace valve, hose & hose clamp, electrical connectors and water supply line.
Scew unit in place ,2 screws.
Check for leaks then replace kick panel, 2 screws.

Parts Used:

Water Inlet Valve

William from WOODINVILLE, WA
Difficulty Level:
Very Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers, Wrench (Adjustable)

4 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

BROKEN CORD, PART OF DOOR COUNTERWEIGHT

REMOVED DISHWASHER FROM CABINET. DETACHED BASE FROM BODY OF THE DISHWASHER. INSTALLED NEW CORD, REATTACHED BASE TO BODY OF DISHWASHER AND REINSTALLED IN CABINET. OPINION: THIS IS A LENGTHY REPAIR AND UNNECESSARY ONE. THE CORD IS PART OF THE DOOR COUNTERWEIGHT AND SUBJECT TO TENSION EVERY TIME THE DOOR IS OPENED, AS WELL AS POTENTIAL CHAFFING DUE TO PROXIMITY TO VARIOUS METAL PARTS, AND VIBRATION. THE CORD SHOULD BE MADE OF STRONGER MATERIAL AND ARMORED OR ALLOWED MORE CLEARANCE. BOSCH SHOULD FIX TO LAST THE LIFE OF THE DISHWASHER.

Parts Used:

ROLLER-TENSION

Bill from EAST JORDAN, MI
Difficulty Level:
Difficult
Total Repair Time:
More than 2 hours
Tools:
Screw drivers, Wrench set

4 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Water was leaking into the dishwasher when it was not running and leaking onto the floor

Disconnected the water and power, pulled dishwasher out from under the counter, unscrewed the old inlet valve, disconnected hose from exit of inlet valve, noted the placement of the wires and disconnected them. Installed new inlet valve in reverse order and reinstalled dishwasher.

Parts Used:

Water Inlet Valve

Andy from STOWE, PA
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers, Socket set, Wrench (Adjustable)

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Overfill then no fill

Remove bottom kick plate and raise the feet up. Remove attachment from the top to counter. Slide out. Facing the unit, remove left hand side sheet metal cover. The unit is behind this cover. Unhook the hose on the lower end. Pop the new one in and hook it up!! Test on quick rinse and see results. If ok return to normal as disassembled. Make sure to level the unit after tucking it back in. Enjoy!!

Parts Used:

Water Fill Sensor Assembly

Lawrence from FREDERICKSBRG, PA
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Pliers

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Water leakage from the dishwasher; unknown source.

Followed the video on your site and it was an easy install with no more leakage.

Parts Used:

Door Seal

Bill from Seattle, WA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Rinse aid dispenser lid would not stay closed

Use a screwdriver flat blade to pry up one edge of closed lid. Put one side of lid into hinge and snapped other side into place. Very easy.

Parts Used:

LID

Sue E from CARMEL, IN
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Missing/broken wheel on right side of lower dishwasher rack

I snapped the part in and voila!

Parts Used:

Lower Rack Wheel with Clip

Danette from SANTA FE, NM
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Lid for the streak treatment wouldn't stay shut.

Use screwdriver to gently wedge the side of the dispenser body apart enough to pop out the old kid, then insert the new kid in it's place.

Parts Used:

LID

Gary from NEW PARIS, IN
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Clogged, old filter- dirty dishes

Removed old filter and replaced with new filter. Easy.

Parts Used:

Micro Filter

David from PENN VALLEY, PA
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Not getting water

shut off water, pull dishwasher out, took side insulation off, unhooked what was connected to the float switch and replaced the new with the old. Reconnected everything and put insulation back and wa-la , all done

Parts Used: