All Installation Instructions for Bosch Dishwasher SHE53TF2UC

E15 Error Code

Turned off power and water supply. Pulled dishwasher out. Disconnected the water inlet from the back left side. Swapped out the inlet valve. Wiped up the water in the bottom pan. Put dishwasher back and turned on water and power. Simple.

Parts Used:

VALVE ACCESS

Bryan from SUWANEE, GA
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers

3 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

The original plastic and rope in the closing mechanism broke and needed replacing.

Note: The diagram and part description misled me to think that each item was a quantity of one, so I ordered two since I wanted to replace the part on each side of the door. In fact, both the cable repair kit and the guide came with a quantity of two, so have an extra set that I will likely never need. As far as the replacement, it was quick and easy. The hardest part was pulling the dishwasher out from under the cabinet.

Parts Used:

Door Hinge Cable Repair Kit

GUIDE

RANDALL from TUCSON, AZ
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Screw drivers

3 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

dishwasher door would not close properly, spray arm would not engage plug

popped off old spray arm from under the rack and put on new spray arm,
couldn't be any easier, 5 minute job, door closes easily now!

Parts Used:

SPRAY ARM

Brian from MADISON, CT
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

3 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

The washer had an error message in the display of E:09. I called Bosh on customer srevice and she said that the heat pump was not working and needed to be replaced. Since the motor is the main part for this that needed to be replaced as well. The pars were under $200.00 total so we oted to fix this

We followed the video and had no problems with leaks at all afterwards. The parts fit perfectly and the machine is working great again.

Parts Used:

Dishwasher Circulation Pump with Heater

HOSE CLAMP

Claire from ALPINE, AZ
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers, Wrench (Adjustable)

3 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Poor cleaning of dishes and calcium build up on filter

I watch utube to assess the problem then took eveything apart and saw the build up on the filter, which i had never cleaned. I tried to clean it but was unsuccessful so order the filter from partselect and it came within a couple of days, installed very easily and began to clean as it always had.

Parts Used:

FILTER-MICRO

Nancy from Safford, AZ
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

5 of 10 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

The Cable Broke on both sides

The instructions stated to remove the door. I spent an hour attempting to remove the door. That was an unnecessary instruction. all else worked as described. Springs were easy to install. The attachment to the door was difficult. Better instructions on how to grasp the connection to spread the spring to give the cable enough slack to attach the connection to the door.

Parts Used:

Door Hinge Cable Repair Kit

Lawrence from MORROW, OH
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Water leakage from the dishwasher; unknown source.

Followed the video on your site and it was an easy install with no more leakage.

Parts Used:

Door Seal

Bill from Seattle, WA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Filter-Micro was clogged with lime from hard water.

Replacement was fast and very simple. Was completed in less than 5 minutes.

Parts Used:

FILTER-MICRO

Peter from LEXINGTON, KY
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Got the wrong part.......NEVER got an answer to my 3 emails to customer service to find the correct part

I ordered the wrong part....needed their help to locate the correct part.
Sent 3 emails asking for help to the 'customer service' email ----NEVER heard a word!!!......and now they want me to rate the installation ?!
Horrible customer service

Parts Used:

Rack Roller Wheel

Donna from SUN CITY WEST, AZ
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Over the years the filter became too clogged with embedded particles

Really simple. You pull out the drain filter plate and pull the filter off the support and replace. I gave everything a good cleaning and put it back in place.

Parts Used:

FILTER-MICRO

Jim from EDINA, MN
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Inlet valve was leaking water at all times causing the unit to shut down with the bottom tray collecting water.

Repair was simple once the problem was diagnosed with the inlet valve.
Most of the work was in disconnecting the necessary lines so the dishwasher could be removed from the cabinets to replace the bad valve. Replacing the valve was easy. Reinstalling the dishwasher was just the reverse of the removal. The replacement part matched the original and solved the problem we had.

Parts Used:

VALVE ACCESS

Ronald from WASHINGTON, MI
Difficulty Level:
Easy
Total Repair Time:
1- 2 hours
Tools:
Pliers, Screw drivers, Wrench (Adjustable)

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Water leaking and high pitch noise mid way through operation.

Mistakenly opened covers for the drain pump. Had to put those covers back in place.
Heater and pump installed easily with a bit of careful maneuvering the plugs and plug housing from the exterior. Pump installed in place easily. Clamp fit perfectly.

Parts Used:

Dishwasher Circulation Pump with Heater

FILTER-MICRO

Lowell from SALEM, OR
Difficulty Level:
Easy
Total Repair Time:
1- 2 hours
Tools:
Nutdriver, Pliers, Screw drivers

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

dishwasher not draining, dishes dirty

replacing the sensor was simple, just unplug and turn it out, but didn't solve the problem, it's a float sensor that doesn't show up on the tech sheet in the dishwasher or anywhere in troubleshooting on the internet I could find.

Parts Used: