- Home
- SCE53M25EU
- Instructions
SCE53M25EU (01) Bosch Dishwasher - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
The plastic clip on the roller broke
26 of 38 people
found this instruction helpful.
-
Catherine from AMHERST, NY
- Very Easy
- Less than 15 mins
We let this go for a shameful amount of time before I decided I could probably fix it. The roller broke so you could only pull it out about halfway or it would come off the track. I looked up the part, and bought it. Actually bought two in case it happened again. When I arrived I looked at how it was put together on the other side and t
... Read more
hen just basically pushed it onto the rod and it was fixed. I am ashamed it took so long to do it. Never be afraid to try it yourself. It was a total of $10 shipped to fix it.
Read less
Was this helpful?
Thank you for voting!
rollers broke
15 of 23 people
found this instruction helpful.
-
Dennis from PLEASANTVILLE, NJ
- Very Easy
- Less than 15 mins
pushed with thumb pressure and snapped rollers into place.....EASY
Was this helpful?
Thank you for voting!
dishwasher not draining, dishes dirty
9 of 13 people
found this instruction helpful.
-
Daniel from AUBURN, IN
- Easy
- 15 - 30 mins
-
Screw drivers
replacing the sensor was simple, just unplug and turn it out, but didn't solve the problem, it's a float sensor that doesn't show up on the tech sheet in the dishwasher or anywhere in troubleshooting on the internet I could find.
Was this helpful?
Thank you for voting!
dishwasher not emptying tub, dirty dishes when the dishwasher said the cycle was done
7 of 10 people
found this instruction helpful.
-
daniel from AUBURN, IN
- Easy
- 30 - 60 mins
easy repair, but the check valve wasn't the problem, it was the float switch that isn't on the tech sheet in the dishwasher or mentioned as a possible culprit anywhere I could find on the internet
Was this helpful?
Thank you for voting!
Dishwasher not draining at end of cycle
4 of 4 people
found this instruction helpful.
-
Steve from Broomfield, CO
- Easy
- 1- 2 hours
-
Screw drivers
My Bosch dishwasher is approx 11 years old. It was leaving water in the dishwasher pan at end of the cycle.
I replaced the drain pump component, which is accessible by removing the lower front panel. It is not necessary to remove the dishwasher door panel to access the pump, but may help with accessing the pump if you have di ... Read more fficulty getting it to come loose.
On the initial install of the new pump, It wasn't fully seated so it dropped a bit. Make sure the pump is fully inserted (push on it or use a bit of Vaseline on the rubber). Once fully seated it no longer dripped and the dishwasher is now draining properly.
Steps
1. Shutoff power at breaker
2. Remove lower access panel at front of dishwasher
3. Remove filter, drain and retaining clip from tub, empty water from tub with sponge or baster
4. Unplug drain plug wiring connector (small clip on right)
5. Twist old drain pump unit clockwise to remove
the old unit (have a towel ready to catch any water left in the tub)
6. Connect new pump to wiring harness
7. Insert the pump at 2 o'clock position, ensure it is fully seated (see note above).
8. Twist pump counterclockwise until it locks into place. The pump should not wiggle and be firmly connected to the unit.
9. Replace tub clip, drain screen and cover
10. Turn power back on, run cycle to test for operation and leaks
11. Reinstall lower access panel.
I replaced the drain pump component, which is accessible by removing the lower front panel. It is not necessary to remove the dishwasher door panel to access the pump, but may help with accessing the pump if you have di ... Read more fficulty getting it to come loose.
On the initial install of the new pump, It wasn't fully seated so it dropped a bit. Make sure the pump is fully inserted (push on it or use a bit of Vaseline on the rubber). Once fully seated it no longer dripped and the dishwasher is now draining properly.
Steps
1. Shutoff power at breaker
2. Remove lower access panel at front of dishwasher
3. Remove filter, drain and retaining clip from tub, empty water from tub with sponge or baster
4. Unplug drain plug wiring connector (small clip on right)
5. Twist old drain pump unit clockwise to remove
the old unit (have a towel ready to catch any water left in the tub)
6. Connect new pump to wiring harness
7. Insert the pump at 2 o'clock position, ensure it is fully seated (see note above).
8. Twist pump counterclockwise until it locks into place. The pump should not wiggle and be firmly connected to the unit.
9. Replace tub clip, drain screen and cover
10. Turn power back on, run cycle to test for operation and leaks
11. Reinstall lower access panel.
Read less
Was this helpful?
Thank you for voting!
Wheels on the bottom tray broke off
4 of 5 people
found this instruction helpful.
-
Phyllis from BAYTOWN, TX
- Really Easy
- Less than 15 mins
The repair was extremely simple. Just lined up and popped them on. No tools needed.
Was this helpful?
Thank you for voting!
There was a roller missing from the lower washing rack.
6 of 11 people
found this instruction helpful.
-
George from STURGEON BAY, WI
- Really Easy
- Less than 15 mins
There were 5 rollers still in place so I used them to show me how to snap the replacement roller in place.
Was this helpful?
Thank you for voting!
Error code E24
3 of 3 people
found this instruction helpful.
-
Steven from STATEN ISLAND, NY
- Very Easy
- 15 - 30 mins
-
Pliers, Screw drivers
when you receive the drain pump and you are ready to install make sure you put VASELINE around the rubber Gromit that will make putting the drain pump in very easy, also to give yourself more space to remove and install the pump remove the front door panel.
It took me 20 minutes from start to finish
It took me 20 minutes from start to finish
Was this helpful?
Thank you for voting!
On/Off button not working properly
3 of 3 people
found this instruction helpful.
-
Richard from MONTROSE, CO
- Really Easy
- 30 - 60 mins
-
Screw drivers
Turned power off, disconnected plug from switch, R&R switch, reconnected plug and restored power
Was this helpful?
Thank you for voting!
Broken wheel on upper rack on both sides
3 of 4 people
found this instruction helpful.
-
Joseph from COLLINGSWOOD, NJ
- A Bit Difficult
- 30 - 60 mins
-
Screw drivers
The part was perfect. The repair video was very helpful, except it did not include the disassembly of the old part. I figured that out, and all went smoothly until the final step. The screw included required not a slot-head screwdriver which everyone has, not a Phillips head screwdriver which everyone has, but a screw requiring a speciali
... Read more
zed driver that no one has. WHY? I substituted a normal screw and hope that does not mean the terrorists have won.
Read less
Was this helpful?
Thank you for voting!
Four wheels on the lower dishwasher rack came off and got lost.
3 of 4 people
found this instruction helpful.
-
james from PARSIPPANY, NJ
- Really Easy
- Less than 15 mins
I bought replacement wheels.
I put them on the post, and they snapped onto the vertical post very easily. Job done.
I put them on the post, and they snapped onto the vertical post very easily. Job done.
Was this helpful?
Thank you for voting!
Got the wrong part.......NEVER got an answer to my 3 emails to customer service to find the correct part
3 of 4 people
found this instruction helpful.
-
Donna from SUN CITY WEST, AZ
- Really Easy
- 30 - 60 mins
I ordered the wrong part....needed their help to locate the correct part.
Sent 3 emails asking for help to the 'customer service' email ----NEVER heard a word!!!......and now they want me to rate the installation ?!
Horrible customer service
Sent 3 emails asking for help to the 'customer service' email ----NEVER heard a word!!!......and now they want me to rate the installation ?!
Horrible customer service
Was this helpful?
Thank you for voting!
E-24
3 of 5 people
found this instruction helpful.
-
John D from Ocoee, FL
- Easy
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)
Removed old discharge pump and replaced it with the new one. After four attempts the dishwasher worked once. This cycle continued for the next 3 attempts then it stoped all together. Ordered the sensor, installed it snd the dishwasher still doesn’t work! Now what do I do???
Was this helpful?
Thank you for voting!
Dishwasher would not start and had not completely drained.
2 of 2 people
found this instruction helpful.
-
Frank from WESTMINSTER, CO
- Really Easy
- 30 - 60 mins
-
Screw drivers
Tried the door lock first. Did not fix the problem.
Replaced the drain pump and it fixed the problem.
Parts Select identified the pump as the most frequent problem.
Next time I will order both parts when one is cheap for any repair.
Find Parts Select is very helpful. They have identified a probl ... Read more em with a washing machine in the past.
I will use them for future problems.
Replaced the drain pump and it fixed the problem.
Parts Select identified the pump as the most frequent problem.
Next time I will order both parts when one is cheap for any repair.
Find Parts Select is very helpful. They have identified a probl ... Read more em with a washing machine in the past.
I will use them for future problems.
Read less
Was this helpful?
Thank you for voting!
One Dishwasher bottom rack wheel broke
2 of 3 people
found this instruction helpful.
-
Toni from GREENSBORO, NC
- Very Easy
- Less than 15 mins
Popped the new one right on!
Was this helpful?
Thank you for voting!