Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
finish on old oven bottom was damaged
1 personfound this instruction helpful.
ERNEST from MANCHESTER, NJ
Very Easy
Less than 15 mins
Screw drivers
Ordered part from customer friendly Part Select and received the replacement part within a few days, and installed it promptly. Wife is happy and stopped grumbling about oven bottom unsightly defect! Small price to pay for a happy wife! Ernie
Was this helpful?
Thank you for voting!
The light inside the oven had burned out
3 of 7 peoplefound this instruction helpful.
Catherine from SEATTLE, WA
Very Easy
Less than 15 mins
0. As a safety precaution, unplug the range or hit the relevant fuse breaker before you start. You might also want to grab a flashlight. Definitely do not try to do this while the oven is hot. 1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back. 2. Pop off the hemispherical glass cap.
... Read more />3. Unscrew the old light bulb, and screw the new light bulb in its place. 4. Put the cap back. 5. Secure the cap by putting the wire back in its slots on the cap.
No tools needed, the cap is just held in place with pressure from the wire.
Read less
Was this helpful?
Thank you for voting!
The old burners were damaged by the prior owners.
1 personfound this instruction helpful.
Mohammad from BARTLETT, IL
Very Easy
Less than 15 mins
The repair was extremely easy. Just removed the old burners and dropped in the new ones. No tools needed.
Had two burners on the stove that would not light. Had tried cleaning them but they still did not ignite. Replaced both burner heads. Once replaced. they ignited right away and have worked ever since.
PULL RANGE OUT FROM WALL & ALSO REMOVED OVEN DOOR BY SLIDING UP. WORKING FROM INSIDE OVEN & ALSO BEHIND I REPLACED PART . ALWAYS " UNPLUG " RANGE BEFORE YOU START.
Was this helpful?
Thank you for voting!
Lightning strike. Ignitors on stove work but display for oven was blank
2 of 4 peoplefound this instruction helpful.
Jeremy from Wilmer, AL
Really Easy
Less than 15 mins
Nutdriver, Screw drivers
Remove rear cover. Remove old display. Remove one wire (and place on new board) at a time. Carefully remove faceplate from old board and place on new one. Close everything up and your done. Took 10-15 minutes.
Was this helpful?
Thank you for voting!
Needed four new burner knobs
1 personfound this instruction helpful.
Judy M from PHILADELPHIA, PA
Very Easy
Less than 15 mins
Super easy since they just push on. But I wanted to say how impressed I was that I couldn't figure out which knob and sent an email and I got back an email the next day telling me what I needed. Super service! thanks so much
Was this helpful?
Thank you for voting!
some of electrodes not working at times,found were bad,wires had some insulation missing, clips looked burnt,found all new parts replaced
1 personfound this instruction helpful.
Dana from LEEDS, AL
Really Easy
More than 2 hours
Pliers
the electrodes on this model have to be removed before you can raise cooktop, once cooktop is raised remove wire from burner bracket, use needle nose pliers to squeeze bottom of clip,remove &replace with new parts.
Orignal oven door handle had multiple fractures and was fast becoming useless.
3 of 9 peoplefound this instruction helpful.
Gerald from Omaha, NE
Really Easy
15 - 30 mins
Screw drivers
Removed the old handle with the new one.
Was this helpful?
Thank you for voting!
Front orifice tube broke
4 of 12 peoplefound this instruction helpful.
craig from unadilla, NY
Easy
15 - 30 mins
Pliers, Screw drivers, Socket set, Wrench set
The repair went easy the tube was a perfect fit
Was this helpful?
Thank you for voting!
Oven handle broke off
3 of 9 peoplefound this instruction helpful.
Maureen from Locust Valley, NY
Really Easy
Less than 15 mins
Nutdriver, Screw drivers
Couple of screws and it was done. Simple and inexpensive since I thought I was going to have to buy a new range.
Was this helpful?
Thank you for voting!
To Replace Gas And Burner Parts In Section 4
0 of 1 peoplefound this instruction helpful.
John from Long Beach, NY
A Bit Difficult
30 - 60 mins
Pliers, Screw drivers, Wrench set
Start by removing all screws 3 for each burner total of 15 t-15 bit is required then proceed to remove spark igniters 5 total slight pull next step would be to slide a screwdriver under top left and right side to remove top shelf. There you will have access to the parts you need to replace. When done just reverse installation instruction
... Read mores to complete
Read less
Was this helpful?
Thank you for voting!
Light burnt out.
2 of 8 peoplefound this instruction helpful.
Roscoe G from ROCHESTER, NY
Very Easy
Less than 15 mins
Turned the wire protector to the side. Turned out the old bulb and replaced it with the new. Turned the wire protector back in place and I'm like new.
My Orders
