RF306BXVN0 Whirlpool Range - Instructions

Turn Off Breaker.

Removed oven racks....

Removed two screws holding element in place...

Disconnect spade lug connectors from old heating element.

Connected spade lug connectors to new heating element.

Reinstall 2 screws holding element.....

Replace oven racks.

Turn Breakers back On.

Done 10 Min. Install

My husband wanted me to call a repair man but I had read online how easy it was. I received my element in one day from Fresno, CA and followed the instructions given by others on line. I couldn't believe how easy it was. The most difficult was removing the connectors because they were stuck. I used needle nose pliers as someone suggested. Saved the cost of a repair man.

This is an easy fix. Just before the holidays, it was imperative that this appliance be in top shape. Since the door 'hung' wrong, it was determined that the hinge pin broke. Remove the 2 phillips head screws on the door and open the door to the to a 15 degree opening. This position allows you to slip the door off the hinge levers. Now that the door is off, replace the hinge pin and slip the retainer ring on with a screw driver blade to push it on the pin. Slide the door back on the levers and fasten the retainer screws. DONE!

First I removed the ovem door, then I removed the 4 screws, unplugged element and plugged in the new one, then replace the screws and door. It should have been a 10 min job but I'm old and a bit fat...slowed me down.

Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you

1. Move oven out from wall 2. Remove back panel of oven, 8 screws 3. Remove 3 screws inside oven holding element 4. Pulled wire connections off of element 5. Reverse procedure to install new element

Ordered element and received it the next day. Removed two screws that holds element in place. I then pulled the element out about 3 or 4 inches and disconnected the two wires. Put new element in connected the wires mounted element in place with the two screws. Now works great!

Unplug first then took back off and took wire clips off and connectected the other on in worked fine you will like part select I just ordered apart for my frig. Waiting for it now.

I must compliment PartSelect on their quick responce and delivery of the item ordered. It arrived a day after I had ordered it. Trust me, the $40.00 I spent on the item was way cheaper than having a repair service fix it or having the entire oven replaced. I would highly recomend anyone to utilize PartSelect.

Removed the two Philips head screws that attach the element to the back wall of the oven. Pulled off the two wire terminals from the spades on the back of the element. Pushed the two wire terminals onto the spades on the back of the new element. Noticed that one was not tight, so disconnected, squeezed down the wire terminal, and reconnected. Inserted the two screws that attach the element to the back wall of the oven. Element works fine.

1) Unplug stove.
2) Remove back cover of the stove held in place by 8 screws (4 short ones for the upper holes and 4 longer ones for the lower holes.).
3) Remove the knob from the switch that you are replacing to expose
the switch mounting screws (2 screws).
4) Remove the screws.
5) Go to the rear of the stove and extract the defective switch.
6) You will see 2 plastic plugs going into/onto the switch. Remove the
plugs. MAKE SURE YOU ARE UNPLUGGED FROM THE
Wall OUTLET!! A small flat blade may be needed to separate the
plugs from switch.
7) Attach the plugs to the new switch (there is only one way to do it.
you wont get them confused and put on wrong.
8) Put the new switch where the defective one was.
9) Come to the front of the stove and put your two screws in and
replace the knob.
10) Replace the back cover,
11) Plug in and test burner.

Unplugged stove from electrical outlet. Pulled temperature control dial off by hand. Remove screws to top back stove panel with Phillips screwdriver. Removed top stove back panel. Unscrewed broken infinity switch from stove. Unclipped wiring harness to broken switch by prying loose with flat head screw driver. Reclipped wiring harness to new switch. Screwed replacement switch back onto stove. Reattached back panel with screws.

I did not think that I would be able to find a replcaement knob for such an old oven. Thanks PartSelect, you rock!

This is the second time PartSelect came through for me. If it hadn't been for you guys, I'd have had to buy a new Jenn-Air cooktop, because ours is nearly 30 years old. About two years ago, I bought a new two-burner cartridge, which installed without tools in about one minute. But a few weeks ago, we lost the burner in the other cartridge. I emailed PartSelect, and even though I gave them my obsolete model number, a helpful service rep managed to find me the part number of the correct burner, so I was able to place my order. Once the part arrived, there was no problem replacing the burner. This is a simple operation we've performed many times when we need to remove the burner for cleaning.

Two screws held the element in place, removed the screws and pulled the piece out.
Back of piece has two wires attached, unplug them then attach the new element and replace the two screws to remount.
First make sure the breaker to the range is turned off before starting the repair.