RED4640YQ1 Roper Dryer - Instructions

I raised the top of the dryer, removed the front, the belt and the drum. Slipped off old rollers, installed new ones and new tensioner. Reinstalled drum and belt, bolted front back on and closed the top.

I watched the video on how to diagnose problem and then how to repair . Videos were very helpful. Also the parts were ordered on line and arrived in 2 days. Parts at a local appliance parts store were twice the cost of what I paid for the parts from PartSelect.

I took the dryer apart ( using a repair book ) It was Super Simple to do I only needed a extra set of hand's to hold the drum in place while reassembling it. removed the hold down snap on collar's on the Motor ( after removing the Blower from the back of the dryer ( super simple. Extra set of hand's needed ) Reassembled in the same order. And now The Dryer work's like NEW..Shure Beat Buying a new Dryer..

When the problem first came up, I took the dryer apart without first looking up any instructions. This wasn't difficult, but didn't realize when removing the fan from the motor, there is a square lug as part of the fan hidden by the rear clamp securing the motor. I was able to remove the fan by holding the motor shaft with a crescent wrench and removing the fan by hand, but was difficult and gloves were necessary in case the fan loosened quickly and my hand came in contact with the sheet metal (very sharp).

I took the motor out and attempted to clean it as it was loaded with dust as was the dryer internals. I tried to lube the motor bearings and appeared to free up, but the sight of metal shavings on the rear bearing seal had me concerned. This ultimely did not work and was trying to buy some time until the new motor arrived.

This is when I looked up the motor part number and found that Parts Select had the part number in stock. I ordered the motor on a Saturday afternoon and got a quick response acknowledging my order. The motor shipped that following Monday from Fresno and arrived on my Southern California doorstep Tuesday. These guys have their act together and are helpful in making the repairs. In my case I did not have to make any adjustments to the wiring or the pulley for my model and replaced the motor the following weekend in about 45 minutes. Since I had the unit apart several times before replacing the motor, the installation went quickly.

The dryer is again working fine for a unit 12 years old and my wife is once again happy that we didn't have to purchase a new dryer.

I lifted the top of the dryer and removed the front panel. I removed the drum exposing the drum rollers. I replaced the rollers and reassembled the dryer. The exploded views on the web site made it easy to see what to do.

Braced dryer drum with a block. Removed the two rollers one at a time by using a screwdriver to pop off the triangular clip. Slid on new rollers. Would have been easier to remove the drum out the front instead of bracing it. Installed new idler pulley and belt. Dryer is 25 years old and sounds like a new one now when running.

Once I started using a bunch of clothespins to hold the felt in place and then started gluing small sections at a time I was able to complete the task. The glue comes out of the tube very quickly so don't squeeze it a lot.

This was so much easier than I though it was going to be. Pulled up on the top part of the dryer and folded it over to the back. Removed 2 screws for the front panel and disconnected some wires. Laying down I fed the new belt on and made sure the tensioner was put back into the right spot, because when the belt broke the tensioner sprung to the other end of its travel. Put everything back together. This was made super easy because you guys had the parts and the shipping was super fast. Alot of the local shops in the area didnt even carry the belt or were not helpful..

I disassembled the dryer once to clean the motor and compartment. After reasembly, the problem persistes. I ordered the motor and the second diasasssembly was accomplished in 10 minutes and the entire job took 45 minutes and the dryer was running like new. Tip- Leave the motor secured while removing the blower fan.

with both hands

Just follow the instructions the one was provided with Maitanace kit we bought from you.

Repair job took less than 10 minutes: 1) Unplug Dryer 2) Remove Lint screen and 2 Phillip screws 3) use flat putty knife to depress lid latches while lifting (latches located approx 2 - 3 inches from each side. 4) unplug defective door switch 5) remove 2 Phillip screws that secure the door switch. Reinstall switch repeating the above steps in reverse order and your done.

First I pulled out lint catcher, you will see two screws ,removed two the screws on top ,( philips head screw driver) I than took a putty knife and pushed in the front of the dryer under the lid and lifted the top up, I than removed a self tapping screw on each side with a 5/16 wrench and lifted the front panel out. I than pulled out the drum and this exposed the two rollers, I than pulled of the nut locks with athe pliers , took off the plastic triangle snaps and pullled off the old rollers , replaceing them with the new ones,put the triangle locks on and that the lock nuts on , I than put the drum back in, than the front panel, replaceing the two self tapping screws , snapped down the top,replaced the other two screws again on top and replaced the lint catcher, I was done.

Prop up the hood of the dryer with flat bar. Take out 2 screws holding dryer front end and 2 switch screws for dryer light inside dryer door. Secure dryer drum with bungee cord. Lift front end and remove. Remove broken belt. Route new belt over drum and pass underneatch idler pulley at botttom of dryer. Apply pressure to idler pulley w/one hand while securing belt around motor with the other. Make sure drum seals are snug between front and back of dryer while putting everything back together.
Have confidence. This is a very easy fix.

First I unplugged the dryer from 240V and removed the back cover upper (behind the switch) and lower (exposing the remainder of the parts)

Inside the upper section was a folded wiring diagram of the dryer (don't know if this was courtesy of Whirlpool or another individual, but it was a very nice touch.)

I did a resistance measurement across the heating coil and found out it was fine. I then plugged the dryer back in and carefully took voltage measurements from one phase of power (this was easily accessed where the power comes in to the dryer, just be careful not to touch or short the wires)

I had an assistant turn on the dryer (this makes things go a little faster, as you are behind the dryer otherwise) and checked for 240V across the heater coil.

Once I did not have this, I kept one lead on the left side wire (one of the power phases coming into the dryer) and moved the other lead to the left (as viewed on the wiring diagram) until I no longer had 240V. This identified the faulty component as the Thermostat High-Limit, non resetable.

I ordered the kit with the High Limit NR and High limit Thermostat (as both had to be bad). I also ordered the 150 degree cycling thermostat (although this was not necessary - for <$20 I opted to replace it as well)

Removing wires one at a time, each component is fairly easy to replace.

My only complaint is that with the combo kit, the wire attachment is a little different that the original component and requires you to cut an existing wire and crimp a different terminal to allow all three wires on the High Limit thermostat (250 degrees) to be attached. There is little to show you how exactly the crimp is to be connected (it goes on the smaller of the three wires - DO NOT CUT the jumper provided and USE A GOOD CRIMPER - not the $2 variety, or you'll be getting a new connector!!) The connector provided is designed for some strain relief from one connector to the other, however) An additional jumper with the appropriate connectors already attached would be a nicer design.

Also, make sure you do NOT screw in the smaller cover that covers the power in until you place the entire lower half cover back on the dryer (unless you want to take it off a second time, as I did...) as it uses a common screw to hold both in place.

Overall, fairly easy to do with a minimum of tools, straight blade screwdriver to remove stubborn wire connectors (esp. for HT thermostat 250), ratchet and socket for quick removal and replacement of covers, and a good T&B style crimper ($10-$20 at your local hardware and well worth it even if you only use it a couple of times)

30 minutes and done - the dryer now cranks out the heat and the advanced settings (Auto dry) work great - no more 2-3 times throug to get things dry.

If you have a minimum of mechanical ability and a little bit of electronic troubleshooting skill, you can check and repair this youself and save about an $80-$100 service call.

Thanks to Part Select for the diagram of the dryer layout as well!! (Schematic would be nice if available online, though!)

Shipped the part in about 2 days from order time, as well. Will be back (hopefully not soon, though, as something has to break first!!!)

Be safe and good luck!

(One last note: Make sure your lint trap is clear including the hose - either due to build up or a lazy kid...as this probably caused the failure as heat could not escape...)