RB1200XKW0 Whirlpool Wall Oven - Instructions
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
element didn't heat
-
JOHN from SIOUX FALLS, SD
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Oven would not heat, but broiler did work. Heating element needed replacing.
The part arrived in less than 2 days. I turned off the main electrical switch to the house. All that had to be done was remove two connecting screws in the back of the oven holding the heating element in place. Then I removed two connecting wires with needle nosed plies. I reversed the process with the new element, turned the power back on, and the element heated up and back in business. This was the easiest I have ever had repairing or replacing anything. The hardest part of this repair was finding a flashlight in my house that had good batteries!! Thank you for such quick and courteous service.
Parts Used:
-
DEBRA from TOOL, TX
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Lower element had shorted out
we replaced with the appropriate part from Part Select. The agent on the phone was extremely helpful with finding a part for our old oven.
Parts Used:
-
Gregory from Sheboygan, WI
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Replace bad broil Element.
First removed the oven door for easy access, removed two screws holding the element pulled old Element from back of oven to expose two connecting wires, disconnected wires and removed old Element. Connected wires to new Element pushed Element back into place and replaced two mounting screws put oven door back on, took about ten minutes. Very Easy!
Parts Used:
-
Roger from Richland Center, WI
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
lower heat element burnt out
remove two screws at rear of heat element unit. gently pull element to expose wires connected to heat unit. pull connectors apart on each end (don't let wire slip back into wall hole). connect new unit to wires, insert back into holes and replace screws into back wall of oven. Done... Now that I have done it once, it would now take less than 15 minutes.
Parts Used:
-
Terry from Lake Quivira, KS
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
broiler element burned out, but stove is 20 yrs old, and I like it
The only problem we had was hanging on to the small screws that held the element up. No power screw drivers, so it took a little while to keep a hold of those screws. Considering we are 87 and 84 we feel great that we were able to replace both the bottom element and the broiler. I like the stove, and preferred not to shop for a new one. "Thanks for prompt great service and the video helped. Patty Montag
Parts Used:
-
Patricia from Colo, IA
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Oven knob was cracked and breaking.
I was able to locate the exact part needed to make my older oven work like new again. Thanks for the great online source for hard to find parts. All I had to do was remove the old one and replace it with th new one. It fit perfectly.
Parts Used:
-
Carolyn B from Tishomingo, MS
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Burned Out Baking Element
Simple to unscrew the 2 screws holding the element to the back of the oven. Unclip the wires.
Parts Used:
-
Scott from Fort Lauderdale, FL
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!