R200 - Instructions

Everyone was amazed we could still get parts for our 25 year old Jenn-air stove top. Easy installation, hands only, couldn't be happier with the easy of ordering, the fast shippment, the quick replacement. Thanks!

1. Turned off electrical breaker at electrical service panel.
2. Tested stove top to verify correct breaker was off as well as cook top.
3. Removed front electrical connection panel @ cook top.
4. Disconnected wires to blower fan. (Before disconnection I color coded wires for correct reconnection)
5. Removed the bracket holding the armored cable (protecting motor wires) and removed wires (where connects to electrical connection box).
6. Removed 4 nuts @ blower motor housing and removed blower motor housing and fan.
7. Removed 3 screws that attached the blower fan to the blower motor housing noting or marking the position of the housing to the motor bracket in order to have the same placement position.
8. Pulled the 3 connecting wires from the armored cable protector to separate housing from motor.
9. Removed the fan assembly from the blower motor shaft by using an allen wrench carefully noting the distance from motor face to the fan.
10. Noting/marking the position of the motor mounting bracket connections unscrew the nut and screw that secures the bracket to the motor.
11. Reassemble in reverse order.
Note:
I taped the motor wires tightly together every 3 or so inches to be able to slide through the armored cable.
I also had to rotate the mounting bracket a little to be able to perfectly match the motor housing to the motor bracket.

The new fan motor works great but it's a little bit louder.

Took out bottom drawer and unplugged power cord, slid unit out to reach back panel,removed front door( 2 Phillips screws) making it easier to reach back of oven, removed screws inside of oven holding element in place, took plate off rear and removed the spade connectors with needle nose pliers. Slid new element into oven and replaced screws inside of oven. Connected the two spade wires on the back and replaced rear panel. Slid unit back in place and plugged the 220v power cord back in. Straightforward and very simple! It took 3 times longer to clean the oven while it was disconnected than it did to replace the element.!

Removed the wires that I could, then terminal block. Installing the new terminal block was very easy; however the wires that arced were fused to the terminal bock screws and needed to be cut and new connectors had to be put on the wires to allow them to be reattached to the block safely.
Once all was replaced and reinstalled the oven has worked great. The length of the repair was increased because of the melted parts and having to run to the store to get the new wire connectors big enough to fit on the wires. If we were simply replacing the block and had not encountered the melted ends, it would have been a very quick and easy repair.

Did not need tools for this job. Simply lift burner element and remove old drip pan and put new one in its place. However - the drip pans that were shipped only fit on the left side of the range. The right side, where the grill attachment goes, is so shallow that the drip pans on that side hit the bottom plate beneath the burner element and would not let the element go down far enough to seat properly. I kept the two pans that don't fit for extras, but I still need shallower pans to fit on the right side.

I also sprayed them 3-times with a clear coat before installing. The clear coat I purchased at WalMart once I noticed it claimed to be safe for plastic. Avoid a clear lacquer based product.

The bulb has a plastic clear cover. That cover can just be carefully removed using a screwdriver. It's held in by a metal bracket. After you remove the cover. You'll just need to replace the bulb and then re-install the cover and bracket.

my original part arrived and it did not fit. When I called to explain the problem I was told it was the wrong part. The big problem is... Frigidaire calls the receptacle a terminal block kit as well as a terminal block kit which is a totally different part. I tried to explain that to several different folks I spoke to at your company as well as Frigidaire but I'm not sure if I got that point across. Take a look at part # 530 393 5058 and part # 530 440 9888 and you will see that they both mention terminal block kit. Hopefully the part I am getting from Frigidaire is an OEM part and will fit.

Removed heating elements and dropped new drip bowls in and replaced new elements

Your website is great...easy and it literally took me no mote than 5 minutes to find what I needed and order...and received it VERY quickly. Must say I was dreading going to some parts house that we have in our town in bad area, and searching on dusty shelves for what I needed...am so glad I found you!!

Pulled off old knob, then pressed on the new one.
It was very easy, and the part was the correct one.

Removed the old element by sliding the wires
attached to it. Unscrew 2 screws, slide the
new one to the wirings and put the 2 screws back.
It works. Praise the Lord.

pulled the element out and found it burn the connectins on one side. so i had to pull the stove and open the back to get to wiring. put a new connecter on. then connected the new element. closed the back.

If I didn't need my oven ASAP, I would not even have attempted to do this repair before my husband came home. But he wasn't going to be home for hours, and I needed it now!
First, I took off the back panel. Slid off the wire connectors. Then moved to the inside of the oven and unscrewed the two screws that secure the element to the oven, and pulled the old one out. Put the new one in and reconnected the wires from the back, and replaced the back panel.
That was it! It worked great!! Very simple.
I called my husband immediately to tell him of my great accomplishment!! I was so proud of myself!

Thanks,
Vicki

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires, replaced witht he new element