R200 - Instructions
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
missing oven racks
-
ALLAN from APACHE JUNCTION, AZ
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
20 of 24 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
oven wouldnt heat
I assumed the bake element was the problem,so I ordered one from Part Select.I was amazed that I got it in 2 days! After removing the 2 screws that held the element in place,I disconnected the 2 wires from the element.I wasnt being very careful and let one of the wires slip back into the hole in the back of the oven.Couldnt get the wire back out,so I had to take the back of the stove off to get to it.Next time,I'll be careful to keep the wires from going back into the holes.Then I connected the element,screwed it in place an turned the oven on.Success !!!
Parts Used:
-
Matthew from Beverly Hills, FL
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver
17 of 18 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Fan switch burned out, Burner switch only worked on HIGH.
Well, since the circuit breaker blew when the fan switch burned out, I was hoping to get a new counter-top range out of this. But, no such luck. My son opened up the control module (2 screws under the fan grill) and found the problem. Then I decided that if I needed to replace ONE part, I'd replace ALL of the parts that didn't work and were worn out.
First I turned off the breaker all the way, then, since the module was open anyway (it pulls out about 2 inches), I only had to remove the old fan switch using the socket set, and replace it, wire-for-wire with the new one. The flange needed to be filed down a bit because it was wider than the original, but not a problem to do. I had to use the original nuts to hold in the new one. The new ones are smaller. Just used the socket set in reverse
....done!
The burner switch and knobs were a little more of a problem but only because ordering them didn't follow the rules...I needed series 3 parts, even though I had a "Run 01" range top. With the help of a very nice customer service rep, I got the correct parts the next day and replaced the burner swich the same way...used a socket set to loosen and remove the old switch and connected the new one wire-for-wire, and again needed to use the original washer and nut. (The wrong model that I initially received had a new washer and nut in the bag with the switch.) But, again, no problem.
The control knobs just pull off and push on...simple.
Now that I had a nearly new range top, I spent another 2 hours REALLY cleaning it (Dawn Power Dissolver is GREAT!). Looks almost like new! I guess I won't be getting a new range top for another 22 years now.....
First I turned off the breaker all the way, then, since the module was open anyway (it pulls out about 2 inches), I only had to remove the old fan switch using the socket set, and replace it, wire-for-wire with the new one. The flange needed to be filed down a bit because it was wider than the original, but not a problem to do. I had to use the original nuts to hold in the new one. The new ones are smaller. Just used the socket set in reverse
....done!
The burner switch and knobs were a little more of a problem but only because ordering them didn't follow the rules...I needed series 3 parts, even though I had a "Run 01" range top. With the help of a very nice customer service rep, I got the correct parts the next day and replaced the burner swich the same way...used a socket set to loosen and remove the old switch and connected the new one wire-for-wire, and again needed to use the original washer and nut. (The wrong model that I initially received had a new washer and nut in the bag with the switch.) But, again, no problem.
The control knobs just pull off and push on...simple.
Now that I had a nearly new range top, I spent another 2 hours REALLY cleaning it (Dawn Power Dissolver is GREAT!). Looks almost like new! I guess I won't be getting a new range top for another 22 years now.....
Parts Used:
-
Judith from Leominster, MA
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers, Socket set
15 of 17 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The drip bowls were old and stained; the knobs were so worn that they could hardly be read.
OK, this was easy, and it's a good thing 'cause I'm so blonde when it comes to repairs. But I will have to say this, my Jenn-Air looks like new and it is 29 years old. Thanks Partselect for making my repairs so quick and easy.
Parts Used:
-
Mary Jo from Minford, OH
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
13 of 15 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Old element visibly burned out
Unplugged oven, unscrewed element, removed back pannel, unclamped old element and removed it, installed new element, clamped it to wires, screwed element to inside of oven, then replaced back pannel
Whole thing took about five minutes.
Whole thing took about five minutes.
Parts Used:
-
Jule from New Salem, PA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Socket set
13 of 17 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Burner was out but the burner coil worked on onother burner
Replaced receptacle but it was not the problem. After further inspection I believe that the problem is the switch. The switch is on order now from Part Select.
Parts Used:
-
Richard from Orange, CA
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers, Screw drivers
10 of 10 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Oven Racks needed to be replaced.
-
Peter from Chicago, IL
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
11 of 14 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Heating element in the lower unit of the doubleoven broke.
First I disconnnected the breaker for the oven and then removed the broken element by unscrewing the screws that held it in with a nut driver. I then pulled the element out exposing the connected wires. I removed the wires from the element by pulling them off with my fingers. Using a set of hemistat pliers I secured the wires so they wouldn't slip into the holes at the back of the oven. I connected the new element by slipping the connectors onto the element and finished by putting the ends of the element back into the holes and securing it into place with the screws using the nut driver.
Parts Used:
-
Lisa from Helena, MT
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Pliers
10 of 11 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Old switch had burned out and needed to be replaced
Turned off electricity at the circuit box. Removed four screws from panel cover that housed the switch. disconected the wires from the old switch and replaced the old switch with the new one reconected the wires put the panel cover back on. voila done.
Parts Used:
-
Jeannine from Twentynine Palms, CA
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
9 of 9 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broken element
First turned off the breaker to the oven, I opened the oven door, took out the baking racks, removed the two screws that hold the element in place. Pulled the element out about 3 inches, disconnected the wires, Installed the new element in the reverse order.
Parts Used:
-
Mike from Hot Springs, AR
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver
9 of 10 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
New Drip Bowls
I have bought several drip bowls over the years. They all seemed to not fit just right. These are perfect! Thanks!
Parts Used:
-
John from San Antonio, TX
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
9 of 11 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Cooktop has aged. Needed new burner switch.
I recently purchased an older home. The cooktop is aged and has not been properly maintained. With the parts I ordered from parts select I was able to bring my cooktop back to almost new! I am very pleased with the quick service parts select provided!
Parts Used:
-
John from Midland, NC
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Pliers, Screw drivers
9 of 11 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Oven wouldn't heat
I could see a visible burnout on the element.
Got it really fast.
Removed two screws, pulled it out, disconnected two wires. installed a new one in, and was done!
Got it really fast.
Removed two screws, pulled it out, disconnected two wires. installed a new one in, and was done!
Parts Used:
-
GREGORY from W Hollywood, CA
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
9 of 12 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
burner receptacle burned out
Worst part of the job was removing the old screws that held the two old rectecles in place for the two burners I repaired. Once the screws were removed cut the wires stripped them and used the porceliean wire nuts provided with the kit. Easy job and good instructions.
Parts Used:
-
Michael from N. Haverhill, NH
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
8 of 9 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
knobs were old could not read numbers
-
catherine from holland, MA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
8 of 10 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!