PVM2070SMC02 General Electric Microwave - Instructions

the online instructions were ideal - just unscrewed the right-hand screw (the only screw) and replaced the bulb by inserting gently but firmly)...getting the old bulb out was a pain, b/c it shattered in my grasp (with little bits of glass all over the stove!), but that has nothing to do with the purchase and installation from this site - all a very good experience

Removed one screw, removed cover, and replaced lamp. Pretty straightforward.

Use a small screwdriver to depress the flexible clip on the side of the old holder while you wiggle it out of its hole. Gently hammer down the edges of the hole so that the surface is flat. This will make for a tighter fit when you snap the new holder into the hole. Just slide the new piece into position and the job is done.

Easy to repair. One screw, remove bulbs, replace with new ones, secure screw.

Partselect.com shipped items quickly as promised, provided follow up email confirming receipt of order, a second email confirming shipment & a link to check shipping status.

Would not hesitate to do business with Partselect.com again!!!

Ordered the part. 2 days later part arrives. Took me 30 seconds to install the part. Sorry it was not more eventful.

We had our kitchen remodeled; new cabinets, countertop, range, refigerator, microwave, dishwasher and floor.

The cabinets around the microwave were custom made; it looks great but it hid the screws, which had to be unscrewed to remove the grill so the interior light of the microwave could be replaced.

A stand was used to support the microwave as I lowered it so the screws could exposed so the light could be replaced.

The light was replaced, the microwave was raised back into place and all is well. I replaced the bulb while my wife was out of town. When she returned she noticed that the microwave was nice and clean; she was NOT aware of the fact that the bulb was replaced!

Bob
Racine, WI

Opened cover, pulled out old bulb, inserted new one, put cover back on. I was out of town when bulbs arived, my wife put it in. She said it was easy.

1. Open the cover over light bulbs with screwdriver.
2. Pulled out blown bulbs.
3. Inserts new bulbs from Partselect.
4. Tested new bulbs
5. Closed the cover over light bulbs with scvrewdriver.
6. Threw out old bulbs and packaging material.

Now, was that easy or what!

Parts arrived on the morning of the second day (Saturday) to my pleasant surprise. I opened the nite light access door with a screw driver. Inserted the 2 bulbs without touching the outside of the halogen bulbs. Checked that the bulbs did work and closed the access door. The entire process went quickly and posed very little difficulty.

used the Dremel Osciilating tool with small blade to quickly cut/remove the old rack holder and then inserted new hold. Took less then 5 minutes total.

removed screw that holds glass for light and replaced bulb.
Reinserted screw that holds glass.

Only down side was cost to ship small bulb.

Found your site online, ordered parts needed. When parts arrived I just put them into the holes in the microwave and popped on the self. Worked like a charm! Thanks very much!

Just unscrewed the screw holding the cover in place, removed the broken glass wearing gloves and then removed both of the burned out lights. Replaced the bulbs while wearing gloves to avoid the commone problem of contaminating the halogen bulbs during installation which can shorten their life. Replaced glass into cover bent back short tabs to hold the glass in place and closed the cover. Reattached cover with screw and it was done 15 minutes tops

Had to take to a local glass shop for sizing and to remove sharp edges. Will never order again.

Removed the light cover screw with a Phillips screwdriver. Removed the lamps from the packaging just enough to free up the 2 prongs for fitting in the socket. Make sure the power is in the "off position". Install the bulbs one at a time by lining up the 2 sockets (Very important not to touch the halogen bulb glass surface while installing them). Energize the light switch to check operation of the new bulbs.