PGS975SER3SS General Electric Range - Instructions

New burner cap replaced old; just placed over burner; no tools required.

One suggestion: burner cap should have been shipped with thicker bubble protection (easy to do). It was minimally wrapped and placed in a thin, bubble envelope, risking damage in shipping process. Luckily, the burner arrived in tact and usable.

Pretty easy in all. The connector from the igniter to teh power sorce didn't quite fit. Ijust cut off the new one and spliced the old one back on. Probably could have made my life easier if I took off the oven door, but it just meant I had to reach more. Works great, and other the connector, which I didn't really think would fit a 15 year old oven,it was very easy/.

This would've been an easy repair, but I ran into some complications.

First I removed the thumb screws holding the bottom oven pan, took the pan out, and also took the bottom panel off the front of the oven.

This gives you access to the burner assembly. I disconnected the wire to the ignitor. I then removed one screw at the front, and two in the back of the burner assembly with a 1/4 socket wrench.

The burner assembly came out. I tested the ignitor for continutiy with a multimeter to ensure this was the faulty part. There was not continuity, so I knew the ignitor needed to be replaced.

This was when I tried to unscrew the ignitor, and both screws stripped their threads on the burner mounting plate. Complication #1. Seems with age, that mounting plate tightened up on the screws.

I cut the screw heads off with a dremel and cutting wheel to get them out. I'm glad I did this before ordering the new part because I needed to order the replacement screws too.

The burner mounting plate for the ignitor needed to be re-tapped to get the new screws in with a 10-32 tap and power drill.

Once the mounting plate was properly rethreaded, I attached the new ignitor, and reattached the burner assembly to the oven.

When trying to connect the wires, the plastic connectors wouldn't click together. They matched up fine, but wouldn't go all the way in. Complication #2. While the plastic connectors were properly mated, the inside pins were both female. The old ignitor had male pins on it, the new one had female pins. So I removed the burner assembly again, cut off the new ignitor connector and spliced in the old ignitor connector with the included porcelain wire nuts.

I put the oven back together again, fired it up, and it worked great.

Just put it on. Quite proud of myself for figuring out what and how to get the part however! The website was very helpful.

I removed the door and the racks, and the flame spreader. I removed the 4"X6" shield loosen the circular flap to plug the new igniter to the recepticle. Turn the oven on to check the operation and if it comes on, button it back up. remember open the oven door approx 3" and pull upwords to remove the door. I would say 90% of the time the igniter is the problem.

Once we knew which part was needed, we went on to your site and orded the part. It was delivered the next day! Partselect.com is bookmarked on every computer in our household, including mobiles. It's great to know there is such a fantastic resource for do-it-youselfers. It took 5 minutes to remove the old igniter and plug in the new. A screwdriver is the only tool required.

Removed bottom shelf from inside oven, turned it obj and replaced the oven deflector with only a screwdriver

I followed the "Test Procedures" on your site { VOM to test the Temperature Sensor and observed the intensity of the Igniter } and found both items were not at specs. Although your video did not depict my model oven exactly, it showed me enough details on how to get to and change out the parts. IE: The connector plug for the Flat Style Oven Igniter had to be accessed through the Warning Draw and not the Oven as shown in the video. A minor issue.
I found your test and safety procedures, how to video's and ease of ordering the required parts fantastic. Most importantly the parts arrived in one day and a half. A very satisfying experience, Thank you

Removed old gasket, did need to use pliers. However, it was easy. The new gasket just snapped in place ...super easy.

First I removed the broiler from the bottom of the oven, then pulled the oven way from the wall to unplug it. I then removed the two screws that hold the igniter element in place. Ironically, the plug GE manufactures is reversed so i had to strip the plug and go end and reverse the wires to attach them to the oven. I used ceramic wire attachments as plastic would surely have melted. Replaced the screws, replaced the broilers, plugged it in, replaced against the wall and it fired up.

Order parts and installed - no tools needed - completed repairs less than 1 minute

1. Removed oven door..
2. Slide out floor plate of over.
3. Removed four screws securing the flame shield.
4. removed the two screws attaching the heating element to the burner.
5. Pulled heating element wires out of rear hole in oven and detached plug.
6. Attached new element and reassembled in reverse order.

Removed the old glowbar's two screws. Didn't take a mental photo of its proper placcement (or a real one, which would've been smart). Removed screws holding 1) a heat protection plate, and 2) wire harness plate. Installed the new glowbar, hopefully, the right way - with its heat-plate facing the gasline of the over/broiler. Reinstalled the heat protection plate and wire harness plate. Hasn't blown up yet!

1. Unplug from electrical outlet. 2. Turn off gas valve. 3. Remove oven door. 4. Remove bottom drawer. 5. Remove oven shelves. 6. Remove oven floor, take out the two screws at the rear. 7. Unplug the igniter from the wire harness, you can reach it from where you removed the drawer. 8. Remove the igniter, by unscrewing the two bolts using your nut driver. 9. Replace with new igniter. 10. Put everything back together, starting with # 9 and work your way to #1.

Step 1 pull the broiler completely out of the bottom of the oven. Step 2 unplug the igniter Step 3 remove 3 small screws to pull the burner tube completely out of the oven. Step 4 replace the igniter and repeat steps to install burner tube back into the oven.