PGS968DER2BB General Electric Range - Instructions

At first I didn't believe it was the igniter due to the fact that it was lighting up, but after reading some of these post, I thought I would give it a try. I accessed the igniter from the broiler drawer after taking out the pans. I removed two bolts with my nut driver and disconnected the wires at the plastic connector after removing the heat shield with a phillips screwdriver (1 screw). I also had to remove a clip to get the wires to pull threw the back of the stove. Here is where the fun began...While waiting on the part to arrive, I decided that it would be a good time to thoroughly clean the entire unit. During this process, I lifted the top of the range to far and cracked both front burner gas lines. After running around town trying to find the gas lines with no luck, I returned home and ordered them from PartSelect as well. The igniter arrived one day and the gas tubes the next. I reassembled the unit and everything works like new, thanks to PartSelect. One other note, when my igniter arrived, It had the exact same electrical plug that my original one had. Some of these post said that you would have to cut the connector off and use the porcelain wire nuts provided. The parts I received were manufacturer parts, no off brand replacements. Again Thank You PartSelect.

removed lower broiler pan so i could see burner igniter. removed the heat shield in front of the gas valve. (1 screw). started oven. no response from igniter. no gas flow at all. if igniter is bad it will not allow gas to flow. ordered new igniter from parts select for my oven model. got it in a couple of days. it wasnt exactly the same as the original, but was compatible. it came with its own connector, but didnt fit. i had to cut it off and splice in the original connector. i had to remove the burner tube to remove the original igniter because the wire was routed around and behind the tube. it just took a couple of screws to remove it and it pulls right off. this is all accessible on the top of the broiler drawer. installed the two screws on the new igniter and plugged in the connector. started oven and igniter started glowing bright immediatly. oven burner lit off within a few seconds. everything working like new now.

I first removed the oven door. I then took out the racks and removed the oven bottom. It slips out easily however, you need to take the door off. The burner cover came next. I used the 3/8 nut driver to remove the four screws. This exposed the burner and electric igniter. Two screws hold the burner tube in place. I recommend removing the burner tube due to the screws holding the ignitor will more than likely need to be cut off. Once the tube is out and you have disconnected the plug for the ignitor you will need to check the voltage at the plug (120 VAC). Place the voltage meter test leads in the oven side of the ignitor plug and set the oven to heat up. If everything is OK the meter should read 120 Volts AC. Turn the oven off and remove the leads. Take the old ignitor off the burner tube and replace it with the new ignitor and plug it back into the oven. Push the plug and wires back into the hole in the burner well and put the burner back in the oven well. Once it is all back in and bolted down try the oven again to verify the ignitor works. Replace the remaining oven parts in reverse order of removal.

I removed the two screws that hold the element in place then I had to splice the wires because the connector was not right and used the two wire nuts that came with the unit .

replace igniter

e-mailed my problem and reply was igniter our gas valve took a gamble and ordered the igniter. easy fix. two srews and plug in wires.

I removed the oven door, the base panel of the oven and slid out the broiler tray. Next, I pulled the wires out of the access hole in the back of the oven, then diconnected the modular plug and removed the 2 screws fastening the ignitor. I tested the ignitor with my ohm meter and found out that it did not have the necessary zero ohms resistance. The meter indicated an open circuit, so I ordered the replacement part, which was delivered in less than 24 hours. Then I reassembled everything and tried the oven. Works like new again.

oven and stove top burners worked fine, but broiler would not light. diagnosed problem as bad igniter. ordered parts on line and received them next day with regular shipping!

removed oven door and bake racks. removed old igniter and snipped wires.

installed new igniter and used ceramic wire nuts to attach wire leads.

reinstalled door and racks.

works fine. who knew home repairs could be so easy and fun!

The part was the exact replacement and fit exactly. Had to cut some of the sheetmetal at the back of the broiler to get the wiring through.

I followed the directions that I read online and the job was a breeze. I started by disconnecting the electricity, and sliding the oven out from the wall, then taking the oven floor cover off, then ordered Chinese, received a phone call from my sister( blah,blah,blah), Disconnected the old piece, paid for Chinese Food, ate Chinese, installed new piece, reinstalled oven floor, reconnected the electricity, pushed oven back into place, lit oven, turned it off and then tested it again. All in less than an hour.

My husband replaced it within 15 minutes,was easy. We ordered the part on a Sunday and had it by Tuesday. Very fast.

thank you

removed the old part .I had to join the new part by clipping the clip off and us the ceramic caps which was included with the new part.Everything went well.

removed oven door & broiler draw took out bottom panel in oven removed part from burner tube reinstalled everything piece of cake works great now

removed oven door racks and pan from bottom of oven. removed warming drawer unplugged oven igniter removed 2 hex screws from bracket on igniter. replaced with new one fiched wire down to warming drawer area plugged in. replaced door and warming drawer. works fine now. very ez to do!

new igniter had a plastic wire coupling that did not fit with the soves wires; cut off coupling and connected wires with ceramic wire nuts given, remounted ignitor and fired up the oven.