PFEF374ES4 Frigidaire Wall Oven - Instructions

Replaced clock control by removing surface burner control knobs and plastic nuts, and then the cover over the oven control. Two screw hold the clock in place, after removal and disconnecting the plug-in you can reinstall the new clock control. The Heat Sensor inside the oven will also need to be replaced. It is located inside the oven ... Read more and attached with two screws; the back of the oven will need to be removed to unplug. Reverse removal procedure and turn the power back on to the stove.

PF alarm appeared on display. Noticed clicking when cord was moved. Had arced for some time and melted original block. New part slightly different. Only has 3 lugs, old one had six. Stack using washers provided. Take note of colors before disassembly. Use caution while working through access opening. The edges are sharp. Only tools neede ... Read more d are phillips screwdriver, deep socket for lug nuts. Nut driver optional. Hope this is helpful.

I pulled my unit out of the wall and noticed that the insulation around the top broiler element was a bit brown. Closer inspection revealed that the element had shorted somehow to the oven itself and caused the element to become non-functional. I tried measuring the resistance first, and it was within typical values for the other elemen ... Read more ts, but I decided to replace the element anyway.

I ordered from PD and the part arrived just a few days letter by regular shipping. I undid the screws holding in the element, undid the wire connectors and replaced the broken element with the new one. The element worked like a charm and I was back in business for cooking.

I called a repair place. They charged $54 to diagnose, (said it needed a new latch motor) then wanted $220 to complete the repair. I checked online prices and did it myself for about 15 minutes work and the latch motor itself ($44?).

Was necessary to uplug the range, pull it away from the wall and remove the back panel sheet m ... Read more etal, then 3 screws that mount the motor. Replace motor, reattach sheet metal. Plug in. Done. Ready to bake cookies.

First we removed two screws under the rim of the range top to open the lid. Lifted the lid and removed the screws from the bracket that holds the elements, Be careful with the clips that hold the element in, if you break them or bend them there aren't any more! Also note which holes they were in, they are marked according to the differ ... Read more ent sizes of elements. Disconnected the wires, needed needlenose pliers to grip them...connected new element, popped it back in place, replaced bracket, closed top ...Easy peasy!!!

Repair was quite easy, as long as you have the instructions for removing the door. The screws that hold the bottom of the door to the fixed hinge are placed into the side of the hinge assembly after removal; this holds the door at a 45 degree angle for easy removal. After that, just place the door on a flat surface and dismantle the door ... Read more from the inside. The inner glass is contained in a metal frame with another piece of glass; this frame comes apart easily using the clips in each side. The door assembles easily after the glass is replaced; just take your time and give yourself enough room to lay out the parts as you go. Good luck!

Turned power off at electrical panel. Pulled oven away from wall. Removed back cover (6 screws), then unplugged wires from old receptacle. I had to pull the squeeze clips backwards & break them to remove the old receptacle - couldn't squeeze them enough to remove them otherwise. The old receptacle came out through the inside of the oven, ... Read more and the new one snapped in easily from inside the oven as well. Replaced wiring, installed new bulb, restored power & tested. Replaced back cover. Good time to vacuum under/behind where the oven usually lives before sliding it back to the wall.

VERY IMPORTANT! kill the circuit breaker to the unit and/or unplugged it! 2 screws hold the ceramic glass top to the lip @ top of oven--remove them and the top can be lifted up to expose all the burner elements and wiring--remove the 2 end screws that hold the retainer bracket for the burners - then remove the 2 screws that hold the burne ... Read more r in question to the bracket-there's also a retainer pin that needs a bit of fussing with to completely free the burner--once totally free remove the wires from the bad unit to the good unit exactly as they are situated --install new unit onto bracket with screws and bracket back to its original location on the ceramic top-put top back down and replace both anchor screws--initiate power back to unit and yeeehahh--You just saved yourself lottsa money from repair bills!!!

FIRST I UNPLUGGED THE GLASS TOP RANGE. While locating the part on the PartSelect diagram I was also able to determine how to access the burned out element. It was very simply to remove three phillips head screws in the front top( above the oven)area of the range, slide the topof the range forwardand lift it up, remove one screw holding th ... Read more e metal bar under the element, replace the element by usinga a pair of pliers to remove the electrical wires and then reversed the process. I saved a tidy amount doing the job myself.

Removed old element and plugged in new. Very simple.

Had to reference original owner's manual for instruction(s) on how to remove oven door. Used several "YouTube" videos to reference oven door design (Oven door glass is actually several layers of glass.) After completing about 30 mins of research and finding the right square drive bit, the repair went smoothly and without complications. Th ... Read more e biggest challenge was researching and understanding what part(s) were needed and how to replace them. It seemed liked a lot of work doing the research however it sure beat a $350 repair bill. It cost me $90 and about 1 1/2 hours of total time. Oven works better than ever, thanks parts select for the part(s) and diagram(s) ...

Lifted the oven top, removed the controls cover, slipped the lens into the hole and slid the light holder device onto the lens

Remove door per the manufacturer instructions (open the door and slide the keepers over the hook part of the hinge and then just pull the door out of the frame - no dismantling while attached to the oven), dismantled the door )about twelve screws around the perimeter of the door) and replaced both hinges. was much easier than I had antic ... Read more ipated. I ordered the parts regular fed ex ground and received within 3 days. I was totally surprised to get exactly what I ordered that fast. I would definitely use Partselect again. Great price and great service. Easy to order.

killed the 50 amp power. removed 3 screws from above oven door slid out cook top, dropped brace holding 2 front burners. The connector corroded off had to look for a high heat connector to connect to the element, after that just screwed everything back together.

Unplug the unit or turn off power at the electrical panel!!!! I removed the 2 screws that hold the top surface of the stove down. On my range, these are located in the front, under the the top surface. You have to open the oven door to remove them. I propped the top up with a couple of 10 inch pieces of 1 x 2 then removed the screws o ... Read more n each end of the bracket that holds the elements in place. I used a 1/4 inch nut driver for these. With needle nose pliers, I removed the 3 retaining clips from the bracket and removed them from the element with a screwdriver and transferred them to the new heating element. The holes around the outside of the element are numbered so it's easy to know where they go. Laying the new element next to the old one, I moved each paddle-type electrical connection one at a time to the corresponding place on the new one. Put the retaining clips back in the slots. Screw the mounting bracket back in. Put the top down and secure it with screws. Very easy repair.