PDW7880J01SS General Electric Dishwasher - Instructions

Simply discarded old wheel assembly and snapped new wheel assembly in place. Very simple.

Repair easy. . Snap it in. . . . . . Impressed with the speedy delivery. Thanks

It was easy as pie. The new wheels came with the new axles already attached, and the whole wheel just snapped onto the lower rack. I ordered 6 and they arrived quickly and attached within minutes, and the dishwasher actually works better now that the rack is raised properly. Thank you!

The connector pump had a pinhole leak at the seam (new part did not have seams). Also replaced the sump inlet which looked worn and the impeller.

Lay dishwasher on it's back to access the bottom. Loosen all clamps. Remove both U shaped holders on the sump inlet. Remove screws holding the drain motor. Pull out the pump motor and sump inlet. Connector pump can be unscrewed from the bottom.

Replace parts and reassemble. It isn't that bad once you start disassembly, especially for anyone somewhat handy.

First I had to unscrew screws under the counter then pulled built in dishwasher out from under the counter, attached hing arm link to right side bracket on door, and the other end I attatched to a spring at the back of the unit. Thats it! and pushed the dishwasher back into place. All back to normal....by the way Im a 67 yr old great grandmother...

The control panel is located in the door of dish washer, first make sure that the power is knocked on unit, take about 10 or twelve phillips head screws out from inside panel of door, unplug power wires from module , reconnect wires to replacment module and reassemble door, really easy to repair, saved me a bunch of money.

replaced it

This was a piece of cake. The original soap dispenser never worked right and always left unused soap. The new part was easy to install and works great. Only needed a 1/4" nut driver and philips screw driver to pull the outside panel and replace the module rinse and cap assy. Easy!

Gasket it self was simple. Just pull out the old rubber gasket and "stuff" in the new one. Note the new gasket was 1-2" short, so I used a piece of the old gasket to fill in the missing length.

The "short seal" was a bit of a mystery on how to actually remove the old one. Taking off the door panel, and almost all the screws on the door did nothing to get access to the short seal. Finally, I simply pryed up the plastic door liner just enough to slide out the old seal. it has a "slot" that engages a plastic bar within the door. Putting in the new was a bit trickier, but after some three handed effort I was able to slide and then snap in the new seal.

So, in the end I really needed to remove NO screws to do the job.

After 10 washes, all seems good with NO leaks.

Bottomline, for a 4 year old dishwasher needing these parts is a bit silly. Older dishwashers I owned lasted 10-15 years with ZERO problems.

So much for GE buying all their appliances in China.......

pulled the racks out, replaced the broken parts....easy job

Turned spray arm while lifting upward to remove the old part. Place new spray arm over the water outlet and turned with light downward pressure until properly seated.

It less time to do the repair than it took to open the box and unwrap the part!

Exactly as described by a previous reviewer. I pulled out the old rack, put in the new rack and just moved over the cutlery rack.

The seal slides out to the side, but the diswasher had to be pulled out from the counter and the entire door had to be taken apart to do this because the hinge was in the way. In taking apart the door, we opened the front panel by taking out the screws along the sides and disconnected the computer connections. After loosening the hinge, we were able to slide the old seal out and the new seal in. When putting the door back together, it was difficult to reconnect the computer connections while holding up the door front, as these ribbon wires were quite short. We did get it back together and working except that the connection to the display light now doesn't work because it probably became disconnected as we put together the door. Also, the door now is not completely level when open making the bottom tray slide in. This is probably because we got the springs too tight. These things can be fixed, but will wait for another day.

We considered buying a new lower rack for the dishwasher which we were told was a new dishwasher when we took over the house. The wheels were constantly falling off when sliding out the tray. They wobbled as well. With the weight of dishes in the rack and malfunctioning wheels, it was a disaster! We found your site on the internet and instead of a new rack we decided to order a whole new set of 8 wheels and axle roller studs. Installation was easy. It's like having a new dishwasher! Tray rolls in/out effortlessly. Great solution for the prices, fast delivery. Everybody is happy! Thanks.

Part was an exact match. Make sure to use plumber's tape on all threads. Had to really tighten fittings to prevent leaks. Screws are a little difficult to get to. Test for leaks first, before final installation.