Home
P2S975CEM4CC
Instructions

P2S975CEM4CC General Electric Range - Instructions

All Instructions for the P2S975CEM4CC

Oven drawer open and close incorrectly

2 of 2 people found this instruction helpful.

James from Goldsboro, NC
Easy
Less than 15 mins
Screw drivers

First I removed the oven drawer. Verified that the support clips would rest correctly on rail, then review installation document with supports to locate alternate location for replacement supports. I did have to personally locate 2 fastners not provided with the supports ot complete installation. After installation, oven drawer opens a ... Read more

Read less

Was this helpful?

GOT 1-SMALL 2-MEDIUM 0-LARGE CAPS

2 of 2 people found this instruction helpful.

Teddy from Bel Air, MD
Difficult
Less than 15 mins

PLEASE BE ADVISED WHEN THEY SHIPPED THE BACK ORDER 1 -(taupe) LARGE CAP - RECEIVED 4 BLACK CAPS - 1-SMALL
2-MEDIUM 1-LARGE (ALL BLACK) - STILL LOOKING FOR
A LARGE CAP IN taupe color!

Received refund for 1-large cap
PROBLEM IS ALL OTHER PARTS ON THE GAS STOVE
ARE taupe in color - do not want black!
... Read more r />your advice?
Read less

Other Parts Used:

Burner Cap Set - Black

Medium Burner Cap

Small Burner Cap

Was this helpful?

Thank you for voting!

Replaced Oven Thermostat Sensor in oven

2 of 2 people found this instruction helpful.

C Thomas from SAN MARCOS, CA

Very Easy

15 - 30 mins

Screw drivers, Socket set

1) Shut off power to oven
2) Removed oven door using snap down hinges on door
3) Removed 4-phillips head screws holding the oven frame to cabinets
4) Pulled oven out of cabinet and set it on stool in front of opening
5) Remove 2-hex screws holding metal shield covering the electrical wiring on back of oven
6) Unpl ... Read more ugged bad thermostat connector
7) Removed the single hex screw holding thermostat inside the oven
8) Pulled the thermostat and lead wire from oven
9) Fed the new thermostat wire into inside back of oven
10) Reverse steps 1-7
Read less

Was this helpful?

Thank you for voting!

Stove was not getting enough power.

2 of 2 people found this instruction helpful.

Nathan from Wells, ME

A Bit Difficult

15 - 30 mins

Nutdriver, Pliers, Screw drivers, Socket set

My stove didn't seem to be getting enough power for the oven to heat up and the burners to get hot enough. When I checked the connection of the electric cord I found that one of the 3 terminals that the plug connects to was broken off. When the new part came I removed the old part by first disconnecting the 3 wires [black,white(ground),r ... Read more ed] and then using a small but long 1/4 socket (that I found at Lowes)I removed the 2 screws that held the old part to the stove and the green screw under it holding the flat copper piece that also connects under the white ground wire of the part. I mounted the new piece on with the 2 1/4 screws. The new part comes with a piece of copper that is for grounding the part to the stove. When I compared it to the old part it was a little different. I first screwed the copper piece onto the stove (under the part) with the green screw then I screwed the white wire over the copper piece to the center terminal(you have to make the hole of the copper piece line up to the screw hole). I connected the other 2 wires and then connected the electric cord to the new terminal block and then put the back cover back on the stove and plugged it in. The clock came on I turned on the four burners they all got hot and red. I turned on the oven the element on the bottom got red I then turned on the broiler the top element got red. My stove is fixed.
Read less

Was this helpful?

Thank you for voting!

The eye would not light

2 of 2 people found this instruction helpful.

Solomon A from COLLEGE PARK, GA

Really Easy

30 - 60 mins

Remove the existing burner and install the replacement.

Was this helpful?

Thank you for voting!

Oven tempeture off by 50 degrees

4 of 8 people found this instruction helpful.

James from CHESTER SPRGS, PA

A Bit Difficult

30 - 60 mins

Nutdriver

Sensor is in rear and on top ov oven. What could be a 10" job took 45". My problem was the oven door was diffinately in the way. Also I wear bifocals which makes me tilt head to see nuts. I felt like a contortionist. HINT: remove door and give yourself some room to work.

Was this helpful?

Thank you for voting!

Both standard & convection oven not heating in upper oven

2 of 2 people found this instruction helpful.

Gordon from Ojai, CA

Easy

30 - 60 mins

Socket set

Circuit breaker off. Watched You Tube video to easily remove and set aside oven door, and shelves, unscrewed back wall cover over convection heating element, and slid out cover over floor heating element. Used ratchet to easily disconnect both old heating elements & pull from rear wall, holding onto two clip electrical connectors while ... Read more gently pulling out plenty of slack as wires fed through insulation material. Concern of "losing" wires back into oven wall not truly a problem if careful. Both sets of connectors pulled off, easily and then slid onto replacement elements without trouble. Circular convection element screwed back into place and cover replaced. Replacement floor element was similar, but not identical, to original. Wires connected fine, but base plate and two screw holes to attach to rear wall were of different size. It rests underneath oven lower cover on its own feet, so really didn't require support. Being DIY obsessive, I nonetheless used its base plate as template to drill two new holes in oven back, secured with old screws. Replaced cover, shelves, door, and woking like new!
Read less

Other Parts Used:

Convection Element

Broil Element

Was this helpful?

Thank you for voting!

Halogen oven light burned out. When trying to remove old bulb, it broke off.

2 of 2 people found this instruction helpful.

William from FRANKLIN, OH

Really Easy

30 - 60 mins

Nutdriver

First, I turned off the power. I removed the fixture that held the bulb and gently used narrow type pliers to pull the old pins out and allowed the broken glass to fall upon a shop towel in the bottom of the oven.

The replacement bulb and different type of wiring connections. I cut and formed them to fit the receptacle. I gentl ... Read more y inserted the new bulb, placed the glass cover back on. Then, screwed the unit back into the top of the oven.

Happily, when power was turned back on the light shone brightly!
Read less

Was this helpful?

Thank you for voting!

Erratic oven temp

2 of 3 people found this instruction helpful.

Gail from Glen Allen, VA

Easy

15 - 30 mins

Nutdriver, Socket set

RE: 2 yr. old GE double wall oven with convection option in upper oven, non-convection in lower oven: baked goods were not browning, were undercooked or burned. Tested both ovens on regular bake setting using 2 oven thermometers. Set ovens for 350. Although after 10 min both ovens beeped "ready", the oven thermometers actually read 20 ... Read more 0 - then would swing up as high as 500 and as low as 200 during the 20 min test period. Decided to first replace top oven sensor only, just in case it really was a more expensive control panel problem. It was a bit awkward to reach back there with the oven door in the way, but I have long arms! Aimed my flashlight, removed nuts with a socket wrench, pulled out the sensor, popped the clip and the old sensor easily separated from its connection. Snapped on the new sensor, pushed it back in and reset the nuts. Easy. Set the oven for 350 and tested again with 2 oven thermometers for 45 min. Voila! The oven thermometers read exactly 350 when the oven beeped "ready" and it stayed at 350 throughout the entire 45 min retest period with only a 3 degree variation both up and down. What a great improvement! Immediately went online to Parts Select and ordered another sensor for the bottom oven which was having the same problem. Fixed both ovens all for under $30 - and just in time for Christmas cookies! Don't want to know what the repair guy would have charged.......Merry Christmas!
Read less

Was this helpful?

Thank you for voting!

Broken rear drawer support

2 of 3 people found this instruction helpful.

Jesse from Knob Noster, MO

Really Easy

Less than 15 mins

Nutdriver

Installed the new brackets at the back of the drawer with the 2 screws provided. The new rear mount design is much better than than the old side mount.

Was this helpful?

Thank you for voting!

Rubber Grate foot worn or missing.

2 of 3 people found this instruction helpful.

Terry L from Puyallup, WA

Really Easy

Less than 15 mins

Replaced worn or missing Grate Foot with new ones. Took less than 5 minutes.

Was this helpful?

Thank you for voting!

feet keep falling off

2 of 3 people found this instruction helpful.

Richard from Stratham, NH

Really Easy

Less than 15 mins

Inserted the grate foot into the spot provided; after consulting the parts manuel to insure I was using the proper procedure.

I do use silicone to help hold the foot but it still won't hold

Was this helpful?

Thank you for voting!

The storage drawer came without supports.

2 of 4 people found this instruction helpful.

Dock from Aurora, CO

Really Easy

Less than 15 mins

Nutdriver

I just removed the drawer and installed the rear supports as instructed on paper included with the part.

Was this helpful?

Thank you for voting!

door gasket was soiled

1 person found this instruction helpful.

Joseph from Murrells Inlet, SC

Really Easy

Less than 15 mins

took out old gasket and inserted new

Was this helpful?

Thank you for voting!

Oven lamp globe shattered . Needed a replacement

1 person found this instruction helpful.

Joan from SOUTHINGTON, CT

Very Easy

15 - 30 mins

The oven lamp shattered while cleaning. Easy to replace by hand.

Was this helpful?

Thank you for voting!

All Instructions for the P2S975CEM4CC

46 - 60 of 114
Prev
2
3
4
5
6
7
8
Next